STEP 5. The mount is designed to fit roofs 1" to 4 3/4" thick. If roof is less than 4 3/4" thick, cut elevating shft and directional handle to size. (See table below.) If roof is more than 4 3/4" thick, the
is required. See page 15, A for chart.
CAUTION: IF YOU ARE USING THE
ADD 1/2" TO ELEVATING SHAFT LENGTH GIVEN BELOW, BUT NOT
TO THE DIRECTIONAL HANDLE.
|
|
|
|
|
|
| Direc- |
|
| |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| tional |
|
| |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| Handle |
|
| |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| |
|
|
| ROOF | ELEVATING SHAFT |
| DIRECTIONAL | ||||
|
|
| THICKNESS | LENGTH |
|
| HANDLE LENGTH | |||
|
|
|
|
|
|
|
| |||
4 3/4" |
| 6 1/4" |
| 5 | 3/8" |
| ||||
|
|
|
|
|
|
| ||||
4 1/2" |
| 6" |
| 5" |
| |||||
4 1/4" |
| 5 3/4" | 6 1/4" |
| 4 | 3/4" |
| |||
4" |
| 5 1/2" | 6" |
| 4 | 1/2" |
| |||
3 3/4" |
| 5 1/4" | 5 3/4" |
| 4 | 1/4" |
| |||
3 1/2" |
| 5" | 5 1/2" |
| 4" |
| ||||
3 1/4" |
| 4 3/4" | 5 1/4" |
| 3 | 9/16" |
| |||
3" |
| 4 1/2" | 5" |
| 3 | 3/8" |
| |||
2 3/4" |
| 4 1/4" | 4 3/4" |
| 3 | 1/16" |
| |||
2 1/2" |
| 4" | 4 1/2" |
| 2 | 3/4" |
| |||
2 1/4" |
| 3 3/4" | 4 1/4" |
| 2 | 3/8" |
| |||
2" |
| 3 1/2" | 4" |
| 2 | 1/16" |
| |||
1 3/4" |
| 3 1/4" | 3 3/4" |
| 1 | 3/4" |
| |||
1 1/2" |
| 3" | 3 1/2" |
| 1 | 3/8" |
| |||
1 1/4" |
| 2 3/4" | 3" |
| 1" |
| ||||
|
|
|
|
|
|
|
|
|
|
|
| STEP 6. Mount antenna and lift on roof in travel position. Apply approved |
| sealing compound suitable for your vehicle roof on bottom of base plate and |
| roof area around hole. See Figure 3. Secure base plate with screws provided, |
| except for screw indicated in Figure 3*. |
| STEP 7. Attach cable clamp to the coax cables 16" from the cable clamp |
| on the gear housing. |
| STEP 8. Attach cable clamp to roof of RV as shown in Figure 3, use 7/16" |
| flat washer between screw and cable clamp, apply sealing compound over |
| mounting screw heads. |
| STEP 9. Attach satellite antenna coax cable (has |
| to the coax cable going to the satellite receiver. |
| STEP 10. Attach |
| to coax downlead going to |
| instruction sheet. You can connect the antenna output from the power |
| supply directly to the satellite receiver (refer to receiver manual). This |
Rev 1/2001 | allows you to watch local channels when you turn the receiver off. |
4