Memorex MVDP1072 manual Audio Setup, EQ type To set EQ modes

Page 41

FUNCTION SETUP

Audio Setup

Audio Setup Page

Audio Mode	Stereo
EQ Type	Off
Sound Field	Off
SPDIF Output	RAW
LPCM Out	48K
Dolby Digital Setup

1.Audio output mode: Set the audio output mode to make the multi-channel audio into two-channel outputs.

Optional settings: LT/RT, STEREO, V SURR.

Default: STEREO

2.EQ type: To set EQ modes.

Optional settings: Off, ROCK, Pop, Live, Dance, Techno, Classic, Soft.

Default: Off.

3. Sound Field: To set different sound field effects.

Optional settings: Off, Concert, Living room, Hall, Bathroom, Cave, Arena, Church.

Default: Off.

4. SPDIF Output: To set the bit stream type of the digital output.

Optional settings: SPDIF/RAW, SPDIF/PCM.

Default: SPDIF/RAW.

5.LPCM Out To set the output frequency of the 96K LPCM audio data to fit for different power amplifiers.

Optional settings: 48K, 96K.

Default: 48K.

6.Dolby Digital setup:

A. L+R: To set the output means of the left or right audio when playing a Dolby disc with separate two-channel audio

Optional settings: Stereo, L-Mono,R-Mono, Mix-Mono.

Default: Stereo.

B. Dynamic compression: To set the linear compression ratio to get different compression result.

Optional settings: OFF 1/8 1/4 3/8 1/2 5/8 3/4 7/8 FULL

Default: OFF.

36

Image 41

Contents User’s Guide Important Safety Instructions Safety Instructions Contents Function Setup Brief Introduction to DVD PrefaceOn this Unit Audio/Video Features FeaturesSvcd Compatible Disc TypesControl Button Locations and Explanations Control Button Locations and Explanations MENU/PBC Button Remote Control IllustrationBattery Installation How to use the Remote ControlInstalling Battery Pack Connecting to Power SupplyConnecting to a TV set System Connections Connecting to an Ordinary Audio SystemConnecting to an Amplifier with Dolby Digital Decoder Connecting to an Amplifier with DTS Digital Decoder Audio/Video In AUX Playback Connect the player to the power supplyPlease refer to page9Press OPEN/CLOSE to open the disc lid Close the disc lidPress PAUSE/STEP button in playback status TV System Selection NTSC/PALPause/Step Playback Press OSD button To restore playback, press the Play buttonOSD On Screen Display Press Volume button on TV set or Amplifier to adjust volume KEY/Volume ControlPress Volume button on the remote control of this unit DVD Menu PlaybackMain menu displays on TV screen PBC PlayBack Control FunctionsPress Audio button Language/Audio Channel SelectionResume audio output MuteSlow Playback Fast PlaybackPress FWD and the player starts fast forward playback Press REV and the player starts fast reverse playbackPress A-B for the third time Repeat PlaybackRepeat the Selected Section Angle Selection Subtitle SelectionPress Subtitle to select the desired language Press Angle and the TV screen displaysPlayback from a Desired Point Power Spectrum MeterPSM graphic equalizer Picture Quality Setting To exit the virtual keyboard, press Function Select again Virtual KeyboardTo exit the browser interface, press Browser again Press BROWSER, the screen displays as followsPress UP/DOWN arrows to select the desired item MP3 and Jpeg File Playing Plays a disc with both MP3 and Jpeg files Playing MP3 FilePlaying Jpeg File Other Basic Operating Means When the button is invalid, the TV screen displaysPress SETUP. The TV screen displays Function SetupPress Setup to exit the setup menu General SettingsSharpness Used to set the sharpness of video output Video SetupScreen saver Turn the screen saver function on or off Sound Field To set different sound field effects Audio SetupEQ type To set EQ modes Audio To set the prefered audio language when playing Initial SetupTV Type To set the output video system of this player PBC To set the PBC statusUseful notes Others TroubleshootingCD-DA MP3 Specifications525/60 TermsDVD-R SIGNAL-TO-NOISE Ratio Code Language Name Language Code ListOthers Page Memcorp, Inc Weston, FL