ENGLISH
IMPORTANT SAFEGUARDS
Caution Concerning the Lamp Replacement
There is potential glass particle hazard if the lamp ruptures.
Caution Concerning the Lamp Unit
There is a potential hazard of glass particle if the lamp ruptures.
In case of lamp rupture,contact your nearest Marantz Authorized Dealer or Service Center for a replacement.
See “Replacing Lamp Unit”. (☞ P.31)
WARNING
CAUTION : | CAUTION HOT : |
| MODEL NO. |
| AC 120V 60HZ 2.0A |
ATTENTION : | ATTENTION CHAUD : SERIAL NO. |
Caution | Concerning the Setup of the Projector |
For minimal servicing and to maintain high image quality, avoid humidity, dust and cigarette smoke.
When the projector is subjected to these environments,the lens and part of ventilation holes must be cleaned more often than usual. As long as the projector is properly maintained in this manner, use in these environments will not reduce the overall operation life. Please note that all internal cleaning must be performed by an Marantz Authorized Dealer, or Service Center.
•Do not expose the projector to extreme heat or cold. Operating temperature:41 °F to 95 °F (+5 °C to 35 °C) Storage
95˚F
(+35˚C)
41˚F
(+5˚C)
Notes on Operation
For USA
WARNING
THIS COVER IS PROVIDED WITH INTERLOCK TO REDUCE THE RISK OF EXCESSIVE ULTRAVIOLET RADIATION. DO NOT DEFEAT ITS PORPOSE OR ATTEMPT TO SERVICE WITHOUT REMOVING COVER COMPLETELY.
For Europe
CAUTION HOT
UNPLUG THE POWER CORD AND
For USA
CAUTION : HIGH PRESSURE LAMP MAY EXPLODED IF IMPROPERLY HANDLED. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
ATTENTION : LA LAMPE SOUS HAUTE PRESSION PEUT SI ELLE, N'EST PAS MANIPULEE CORRECTEMENT, CONFIER L'OPERATION A UN PERSONNEL D'ENTRETIEN QUALIFIE.
CAUTION HOT : UNPLUG
THE POWER CORD AND WAIT M
60 MINUTES BEFORE CHARGING THE LAMP.
ATTENTION CHAUD :
DEBRANCER LE CORD ON D'ALOMENTION ET ATENDER 60 MINUTES AVANT DE CHANGER LAMPE.
•The exhaust ventilative hole, the lamp cage cover and adjacent areas may get extremely hot during projector operation. To prevent injury,do not touch these areas until they have sufficiently cooled down.
•Allow at least 1 foot (30 cm)of space between the exhaust ventilative hole and the nearest wall or obstruction.
•If the cooling fan becomes obstructed, a protection device will automatically turn off the projector lamp. This does not indicate a malfunction. Remove the projector power cord from the wall outlet and wait at least 10 minutes.
Then turn on the power by plugging the power cord back in. This will return the projector to the normal operating condition.
WAIT 60 MINUTES BEFORE CHANGING THE LAMP.
ATTENTION CHAUD
DEBRANCER LE CORD ON D'ALIMENTION ET ATENDER 60 MINUTES AVANT DE CHANGER LAMPE.
WARNUNG HEISS
ZIEHEN SIE DEN NETZSTECKER
AB UND WARTEN SIE 60 MINUTEN, BEVOR SIE DIE GLUHLAMPE WECHSELN.
For Europe
CAUTION | VORSICHT : | |
HIGH PRESSURE LAMP MAY EXPLODED IF | BEI FALSCHER HANDHABUNG M | |
IMPROPERLY HANDLED. REFER SERVICING | KANN DIE HOCHDRUCKLAMPE | |
TO QUALIFIED SERVICE PERSONNEL. | EXPLODIEREN UBERLASSEN | |
ATTENTION | SIE WARTUNGSARBEITEN | |
NUR FACHPERSONAL. | ||
LA LAMPE SOUS HAUTE PRESSION PEUT | ||
| ||
EXPLOSER SI ELLE, N'EST PAS MANIPULEE |
| |
CORRECTEMENT, CONFIER L'OPERATION |
| |
A UN PERSONNEL D'ENTRETIEN QUALIFIE. |
|
2