Marantz VP-11S2 manual Read Before Operating Equipment, Additional Safety Information

Page 2

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

IMPORTANT SAFETY

INSTRUCTIONS

READ BEFORE OPERATING EQUIPMENT

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

This product was designed and manufactured to meet strict quality and safety standards. There are, however, some installation and operation precautions which you should be particularly aware of.

1.

Read these instructions.

2.

Keep these instructions.

3.

Heed all warnings.

4.

Follow all instructions.

5.

Do not use this apparatus near water.

6.

Clean only with dry cloth.

7.

Do not block any ventilation openings. Install

 

in accordance with the manufacture's

 

instructions.

8.

Do not install near any heat sources such as

 

radiators, heat registers, stoves, or other

 

apparatus (including amplifiers) that produce

 

heat.

9.

Do not defeat the safety purpose of the

 

polarized or grounding-type plug. A polarized

 

plug has two blades with one wider than the

 

other. A grounding type plug has two blades

 

and a third grounding prong. The wide blade

 

or the third prong are provided for your

13.Unplug this apparatus during lightning storms or when unused for long periods of time.

14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Additional Safety Information!

This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

Apparatus shall not be exposed to dripping or splashing and that no objects filled as vases, shall be placed on the apparatus.

When the switch is in the OFF position, the apparatus isn’t completely switched-off from the MAINS.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

NOTE:

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

safety. If the provided plug does not fit into

your outlet, consult an electrician for

replacement of the obsolete outlet.

10. Protect the power cord from being walked on

or pinched particularly at plugs, convenience

receptacles, and the point where they exit

from the apparatus.

11. Only use attachments/accessories specified

by the manufacturer.

12. Use only with the cart, stand, tripod, bracket,

or table specified by the manufacturer, or

sold with the apparatus. When a cart is used,

use caution when moving the cart/apparatus

combination to avoid injury from tip-over.

DECLARATION OF CONFORMITY

This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

U.S. Responsible Party: Marantz America, Inc.

100 Corporate Drive,

Mahwah, NJ, 07430, U.S.A.

TEL: 630-741-0300

Type of Product: DLP Projector

Model:VP-11S2

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada.

Image 2
Contents Model VP-11S2 User Guide Additional Safety Information Read Before Operating EquipmentEnglish Français Español Português Deutsch Kongeriket Norge ItalianoSuomi SvenskaTable of Contents Vorsicht Important SafeguardsWarnung Heiss Features AccessoriesFront and Top View Adjust the picture focusProjector Layout and Functional Overview Bottom View Ventilation holes intake Adjustable Feet Adjustable feetRear and Terminals View Remote Controller £9PATTERN button P.11 Remote Controller Operational Range VP-11S2When pulling out a cable Connection with AC Power SupplyWhen making connections be sure to ConnectionCompatible PC Advanced ConnectionHD-Video / Satellite Cable Tuner / DVD Player ScreenZooming and Focusing Initial SettingTurning on the Power Detail FocusingKeystone Correction Adjusting the Image PositionAdjusting the Height Returning the Projector to its Initial PositionInstalling on a tabletop InstallationRecommended Setting Mounting on the ceiling16 9 Screen Screen Size and Projection Distance inch VP-11S2Screen Size and Projection Distance mm VP-11S2 ScreenScreen Size and Projection Distance inch VP-11S2L Screen Size and Projection Distance mm VP-11S2LExtended mounting condition From +100% to +165% Lens shift position VP-11S2Standard condition From -85% to +100% Lens shift position VP-11S2L Standard condition From -85% to +165%Basic Operations Selecting the Aspect ModeSelecting the Input Signal Source Screen Images in a 169 screen To Turn off the Power Screen Images in a 43 screenOperations Menu StructureFunctions by Signal Component RGB Hdmi ANY Input Ntsc PAL/SECAMNo Signal Valid Signal ANY Input Adjustment bar Picture ModeMemorizing settings in an index Picture Adjust CEC Fine MenuFRC Hdmi 1, Hdmi Input Signal RGB/HD AdjustRGB NTSCNTSC-3.58Display Blanking Top, Bottom, Left and Right Adjustments Menu PositionOSD/Blanking Configration Replacing Lamp Unit MaintenanceLamp Life and Replace Lamp Wait at the least one hour for the lamp Optional Accessories Cleaning the LensReplacement Parts Lamp Unit LU-12VPS3 Ceiling Mount kit MountTroubleshooting On Screen Message Error ModeBlack Level Black setup GlossaryTiming chart Optical characteristicsAccessories Input/OutputVP-11S2L DimensionsVP-11S2 Page Is a registered trademark