Marantz VP-11S2 manual English

Page 3

ENGLISH

FOREWORD

This section must be read carefully before any connection is made to the mains supply.

WARRANTY

For warranty information, contact your local Marantz distributor.

RETAIN YOUR PURCHASE RECEIPT

Your purchase receipt is your permanent record of a valuable purchase. It should be kept in a safe place to be referred to as necessary for insurance purposes or when corresponding with Marantz.

IMPORTANT

When seeking warranty service, it is the responsibility of the consumer to establish proof and date of purchase. Your purchase receipt or invoice is adequate for such proof.

FOR U.K. ONLY

This undertaking is in addition to a consumer’s statutory rights and does not affect those rights in any way.

EQUIPMENT MAINS WORKING SETTING

Your Marantz product has been prepared to comply with the household power and safety requirements that exist in your area.

COPYRIGHT

Recording and playback of some material may require permission. For further information refer to the following:

-Copyright Act 1956

-Dramatic and Musical Performers Act 1958

-Performers Protection Acts 1963 and 1972

-Any subsequent statutory enactments and orders

WARNINGS

Do not expose the equipment to rain or moisture.

Do not remove the cover from the equipment.

Do not insert anything into the equipment through the ventilation holes.

Do not handle the mains cord with wet hands.

Do not cover the ventilation with any items such as tablecloths, newspapers, curtains, etc.

No naked flame sources, such as lighted candles, should be placed on the equipment.

When disposing of used batteries, please comply with governmental regulations or environmental public instruction’s rules that apply in your country or area.

Make a space of about 0.2 meter around the unit.

When the projector is mounted on the ceiling, the Ceiling Mount Kit approved by MARANTZ must be used for installation.

Do not look into the lens when the projector is turned on. It could damage your eyesight.

Unplug the projector from the wall outlet if it is not to be used for a few days.

No objects filled with liquids, such as vases, shall be placed on the equipment.

When the switch is in the OFF position, the equipment is not completely switched off from MAINS.

The equipment shall be installed near the power supply so that the power supply is easily accessible.

Lamp Handing Precautions

DANGER

This SHP uses a high voltage glass mercury vapor lamp. The lamp can break or fail to light if handled wrongly during replacement or because of the projector’s surrounding temperature.

Lamp life also varies according to the lamp with some even breaking or failing to light as soon as they are used the first time. If the lamp breaks, glass fragments may be scattered inside the lamp unit and projector, and gas inside the lamp bulb that contains mercury vapor may be emitted from the projector’s vent.

Before use, carefully read the projector user guide and the lamp replacement instructions. Remember to handle the lamp with care. In the event of serious trouble, call for Marantz authorized dealer.

Do not look directly into the lamp with bare eyes while lit. The bright light can cause sore eyes and impair vision.

Do not directly expose skin to the light of the lamp. Direct exposure can inflame the skin.

Do not drop, impact, subject to excessive force or otherwise damage the lamp.

Replacing the lamp runs the risk of burns and electric shock, therefore shut OFF power supply, unplug the AC power cord from AC power outlet and wait at least 60 minutes for the lamp to cool down before attempting to replace it.

If the lamp breaks, unplug the AC power cord from AC power outlet and call for Marantz authorized dealer to replace it. Do not replace the lamp yourself or clean up broken glass inside the projector as this can result in cuts and burns to you or damages inside the projector.

If the projector is hung from a ceiling or installed in a high place, it is extremely dangerous to replace the lamp. In this case, do not replace or handle the damaged lamp yourself.

CAUTION

The chance of the lamp breaking is high after extended use. It is recommended to replace the lamp when near the end of its designed life. Do not use a lamp beyond the maximum lighting time.

Use only Marantz original lamp units. Check the model code of the lamp unit matches that in the user guide.

Before replacing the lamp, read carefully “Lamp Unit Replacement” in the user guide. Replace the lamp as explained therein.

Entrust disposal of a used lamp to a licensed industrial waste handler or return it to the place of purchase. Do not break the lamp or discard with general waste.

If the lamp breaks, leave the area immediately and stay away for at least 30 minutes, and ventilate the room so as not to inhale the mercury vapor.

If you inhale the mercury vapor, see a physician immediately and follow his instructions.

Image 3
Contents Model VP-11S2 User Guide Read Before Operating Equipment Additional Safety InformationEnglish Français Español Português Deutsch Svenska ItalianoSuomi Kongeriket NorgeTable of Contents Important Safeguards Warnung HeissVorsicht Accessories FeaturesAdjust the picture focus Projector Layout and Functional OverviewFront and Top View Ventilation holes intake Adjustable Feet Adjustable feet Rear and Terminals ViewBottom View Remote Controller £9PATTERN button P.11 VP-11S2 Remote Controller Operational RangeConnection Connection with AC Power SupplyWhen making connections be sure to When pulling out a cableScreen Advanced ConnectionHD-Video / Satellite Cable Tuner / DVD Player Compatible PCDetail Focusing Initial SettingTurning on the Power Zooming and FocusingReturning the Projector to its Initial Position Adjusting the Image PositionAdjusting the Height Keystone CorrectionMounting on the ceiling InstallationRecommended Setting Installing on a tabletopScreen Screen Size and Projection Distance inch VP-11S2Screen Size and Projection Distance mm VP-11S2 16 9 ScreenScreen Size and Projection Distance mm VP-11S2L Screen Size and Projection Distance inch VP-11S2LLens shift position VP-11S2 Standard condition From -85% to +100%Extended mounting condition From +100% to +165% Standard condition From -85% to +165% Lens shift position VP-11S2LSelecting the Aspect Mode Selecting the Input Signal SourceBasic Operations Screen Images in a 169 screen Screen Images in a 43 screen To Turn off the PowerMenu Structure OperationsComponent RGB Hdmi ANY Input Ntsc PAL/SECAM Functions by SignalNo Signal Valid Signal ANY Input Picture Mode Memorizing settings in an indexAdjustment bar Picture Adjust Fine Menu FRCCEC NTSCNTSC-3.58 Input Signal RGB/HD AdjustRGB Hdmi 1, HdmiDisplay Adjustments Menu Position OSD/BlankingBlanking Top, Bottom, Left and Right Configration Maintenance Lamp Life and Replace LampReplacing Lamp Unit Wait at the least one hour for the lamp Lamp Unit LU-12VPS3 Ceiling Mount kit Mount Cleaning the LensReplacement Parts Optional AccessoriesTroubleshooting Glossary Error ModeBlack Level Black setup On Screen MessageInput/Output Optical characteristicsAccessories Timing chartDimensions VP-11S2VP-11S2L Page Is a registered trademark