Marantz VP-11S2 manual Fine Menu, Frc, Cec

Fine Menu 1

Fine Menu 2

ENGLISH

By adjusting this Fine Menu, you can make fine picture adjustment.

Standard 1

Item Adjustments

Standard 1

Picture Adjust

Fine Menu 1

Fine Menu 2

Input Signal

RGB/HD Adjust

HDMI

Display

OSD/Blanking

Config.

Noise Reduction	0
R Gain	0
G Gain	0
B Gain	0
R Bias	0
G Bias	0
B Bias	0
Luminance Gain	0
Chroma Delay	0

Picture Adjust

Fine Menu 1

Fine Menu 2

Input Signal

RGB/HD Adjust

HDMI

Display

OSD/Blanking

Config.

Aspect	Full
Cinema	Auto
VCR Mode	On
Black Level	0 IRE
FRC	Auto 1
CEC	Off
Picture Shift V	0
Overscan	Enable

Aspect	Full, Normal, Zoom,
	V-Stretch, Through
Cinema	Auto, Off
VCR Mode	On, Off
Black level	0 IRE, 7.5 IRE /Expand,
	Normal (For HDMI input)
FRC	Auto 1, Auto 2, 60Hz,
	50Hz, 48Hz
CEC	On, Off

Item	Adjustments
Noise Reduction	050
R Gain	-50Ô0Ô 50
G Gain	-50Ô0Ô 50
B Gain	-50Ô0Ô 50
R Bias	-50Ô0Ô 50
G Bias	-50Ô0Ô 50
B Bias	-50Ô0Ô 50
Luminance Gain	-50Ô0Ô 50
Chroma Delay	-5Ô0Ô 5

–Noise Reduction

Adjust the noise reduction.

–R Gain

This menu allows the users to set the gain for red.

–G Gain

This menu allows the users to set the gain for green.

–B Gain

This menu allows the users to set the gain for blue.

–R Bias

This menu allows the users to set the bias for red.

–G Bias

This menu allows the users to set the bias for green.

–B Bias

This menu allows the users to set the bias for blue.

–Luminance Gain

This menu allows the users to set the luminance gain.

–Chroma Delay

This menu allows the users to set the chrominance delay.

Note :

•The settings made in Fine Menu 1 are saved in the currently selected Picture Mode index (Default excluded).

26

Picture Shift V	-50Ô0 Ô50
Overscan	Enable, Disable

–Cinema

Auto : Automatically selects the cinema mode when a video signal is input.

NTSC: 3-2 pull down, PAL: 2-2 pull down

Off : Pull-down processing is not performed.

–VCR Mode

On : A projector is forced into the intra-field only deinterlacing mode.

Off : A projector is used with external field memories and operates in the full set of deinterlacing modes, i.e., motion adaptive video deinterlacing and full frame film source deinterlacing using 3:2 pulldown detection (2:2 pulldown for 625/50 sources).

–Black level

Select the black level by a video source.

–FRC (Frame Rate Conversion)

Auto 1 : Frame Rate Conversion function is basically off. However FRC turns on automatically depending on vertical frequency of input signal. Normally, use this mode.

Auto 2 : Use this mode when the image stops momentarily.

60Hz : Frame Rate Conversion function is “On”. (59.94Hz fixed)

50Hz : Frame Rate Conversion function is “On”. (50.00Hz fixed)

48Hz : Frame Rate Conversion function is “On”. (47.95Hz fixed)

–CEC (Chroma Error Correction)

On : Reduces CUE (Chroma Up-sampling Error) of 1080i signals.

Off : Normally, use this mode.

–Picture Shift V

When Aspect on the Picture Adjust menu is set to “Zoom” or “V-Stretch”, this setting allows the user to move the projected image vertically in order to see parts on the image not appearing on the screen.

–Overscan

Selects whether to show or hide picture borders with NTSC, PAL, SECAM, 480i, 480p, 576i and 576p signals.

Enable: Does not display borders of image signals. (Normally, use this mode.)

Disable: Displays the entire image signal.

Notes :

•There are some parameters can not adjust according to input signal.

•The settings made in Fine Menu 2 are saved in each currently selected input signal source.