Marantz RC9500 manual Frequently Asked Questions

Page 66

DFU RC9500 Ver1_2.qxd 5/28/2004 10:33 AM Page 66

Frequently Asked Questions

User Guide

Can I program a device button to execute more than one command?

Yes, you can. You can program a macro to the device button in the MACRO mode. (see page 42)

How do I program source switching?

See “Programming The Device Buttons ...” on page 30.

How can I edit macros that are programmed in the button of the Device Overview?

You can do this using “Macro to device” function via the MACRO mode. (page 45)

How can I label buttons on Device Overview pages?

You can do this using “Label device” function via the LABEL mode. All changes you make to these items are automatically updated in the Device Overview page. (page 34)

How can I delete buttons on Device Overview pages?

You can do this using “Delete device” function via the DELETE mode. All changes you make to these items are automatically updated in the Device Overview pages. (page 40)

How do I reset the RC9500?

Normally, you never have to reset the RC9500. However, if the RC9500’s display freezes or if you notice unusual behavior, you might need to reset the RC9500. You will not lose any saved programmed commands or macros.

Carefully press the reset button near the battery connector inside the battery compartment of the RC9500 with a paperclip or sharp pencil. The RC9500 restarts and beeps to indicate it is ready for use.

Can I revert to the original configuration?

Yes. By using Wizz.it 9 with Windows PC, you can get the factory default configuration. Using Wizz.it 9, once the program is installed, open a configuration file named “RC9500_default” in C:\Program Files\Marantz\Wizzit_9\Samples. Downloading this configuration will restore your RC9500 to its factory state except the setup items.

By using the “Revert” function in the Setup, you can get the last downloaded configulation.

62

Image 66

Contents Model RC9500 User Guide FCC Compliancy Declaration of Conformity N V04ECRC9500DFU RC9500 Ver12.qxd 5/28/2004 1032 AM RC9500 Remote Control User Guide Automating Your Home Theater With The Marantz RC9500Table of Contents Introduction Marantz RC9500Battery IntroductionInstalling the Battery Pack Charging the RC9500 Activating the RC9500 Using the BacklightGetting Started Turning on the Touch ScreenNavigating the RC9500 ModesNavigating the Devices Device Overview Navigating the Pages OverviewOther Navigation Sending commands Using the Soft ButtonsUsing the Hard Buttons Operating a DeviceSetup Pages To exit the InformationFirst Setup Setting Time and Date Changing the Time FormatChanging the Time „ To Change the Month Changing the Date„ To Change the Day „ To Change the YearMode Menu So on, you have to switch to the appropriate modeAdjusting the Touch Screen Brightness To switch to another modeCustomizing your RC9500 IntroductionCloning All Your Existing Remotes Congratulations Complex Operation? Macro or Help Tip Tap Copy without RC codes when it prompted. see Programming Help ListMacro/Page Jump Capability Any Button Performs Macros/JumpsMacros Perform Jumps to Any Device Macros Send Commands To Your System Macros Can Contain Delay and Beep Between StepsProgramming Macros & Page Jumps Customizing Your RC9500 You are now a Home Theater Automator Learning IR command ReferenceProgramming Touch Screen Buttons Programming The Device Buttons Device Action Programming the Hard Buttons per DeviceReference Labeling Buttons, Pages and Devices Labeling a ButtonReference Labeling a Device Labeling a„ Create New Device „ Copy Existing Device Adding DevicesDescription for the Device Template Device TemplateReference Creating a New Device Step by Step Copy Existing Device Deleting Buttons and Devices Deleting a ButtonDeleting a Device Moving Devices Macro Page Notation Adjusting DelaysProgramming Macros DVDRecording a Macro to a Operation Button Step By Step Tap the Macro to Button button to proceed to the next stepRecording a Device Action Source or Input Switching Recording a Jump to a DeviceEditing Macros Creating and Editing Timers Adding a TimerActivating Timers Deleting a Timer Labeling a TimerEditing a Timer Define the Repeat Settings Set the Start DateSet the Start Time Setting the Start Date Setting the Start Time or Stop TimeTo change the Start Date Defining the Repeat Setting Defining the Start Action or Stop Action„ Daily „ Weekly Using the RC9500 with Radio Frequency Changing the IR / RF SettingsReference Software Choosing Another ChannelInternet Fun PC RequirementsCleaning the RC9500 Maintaining Your RC9500Important Notice Troubleshooting General ProblemsProgramming Problems Recharging Problems Frequently Asked Questions How do I calibrate the Touch Screen? Overview of Symbols Overview of Symbols Specifications DisplayVolume IndexDSS ADD Operating Other Service and Support Service and SupportUpdates and New Products Memo Japan