Marantz manual Charging the RC9500

Page 9

30° to 45°

DFU RC9500 Ver1_2.qxd 5/28/2004 10:33 AM Page 9

Introduction

Charging the RC9500

For charging the RC9500, you use the docking station DS9500.

1Connect the power adapter to the docking station and plug it into a wall outlet.

Note Use only the supplied power adapter with the docking station.

2Slide the RC9500 into the docking station until it clicks. Charging starts immediately. The blue charging LEDs on the front of the docking station indicate charging takes place.

When the RC9500 is fully charged, the LEDs are turned off.

DS9500

Make sure you lift the RC9500 up at an angle of 30° to 45°

when you take the RC9500 out from the docking station.

Note Normal charging time is 2 to 3 hours, depending on the condition of the battery pack.

You can operate the RC9500 while it is being charged. The battery pack does not have to be entirely empty before recharging.

You can place the RC9500 in the docking station at any time.

When the battery is running low, the Low Battery icon appears.

Recharge the RC9500 as soon as possible to Low Battery icon ensure the perfect performance.

Note The RC9500 retains all settings when the battery is completely empty. You will only have to adjust the clock.

User Guide

5

Image 9

Contents Model RC9500 User Guide Declaration of Conformity N V04ECRC9500 FCC CompliancyDFU RC9500 Ver12.qxd 5/28/2004 1032 AM Automating Your Home Theater With The Marantz RC9500 RC9500 Remote Control User GuideTable of Contents Marantz RC9500 IntroductionIntroduction BatteryInstalling the Battery Pack Charging the RC9500 Getting Started Using the BacklightActivating the RC9500 Turning on the Touch ScreenNavigating the RC9500 ModesNavigating the Devices Device Overview Overview Navigating the PagesOther Navigation Using the Hard Buttons Using the Soft ButtonsSending commands Operating a DeviceTo exit the Information Setup PagesFirst Setup Setting Time and Date Changing the Time FormatChanging the Time „ To Change the Day Changing the Date„ To Change the Month „ To Change the YearSo on, you have to switch to the appropriate mode Mode MenuTo switch to another mode Adjusting the Touch Screen BrightnessCustomizing your RC9500 IntroductionCloning All Your Existing Remotes Congratulations Complex Operation? Macro or Help Tip Programming Help List Tap Copy without RC codes when it prompted. seeMacro/Page Jump Capability Any Button Performs Macros/JumpsMacros Perform Jumps to Any Device Macros Can Contain Delay and Beep Between Steps Macros Send Commands To Your SystemProgramming Macros & Page Jumps Customizing Your RC9500 You are now a Home Theater Automator Reference Learning IR commandProgramming Touch Screen Buttons Programming the Hard Buttons per Device Programming The Device Buttons Device ActionReference Labeling a Button Labeling Buttons, Pages and DevicesReference Labeling a Labeling a DeviceDescription for the Device Template Adding Devices„ Create New Device „ Copy Existing Device Device TemplateReference Creating a New Device Step by Step Copy Existing Device Deleting a Button Deleting Buttons and DevicesDeleting a Device Moving Devices Programming Macros Adjusting DelaysMacro Page Notation DVDTap the Macro to Button button to proceed to the next step Recording a Macro to a Operation Button Step By StepRecording a Jump to a Device Recording a Device Action Source or Input SwitchingEditing Macros Adding a Timer Creating and Editing TimersActivating Timers Labeling a Timer Deleting a TimerEditing a Timer Define the Repeat Settings Set the Start DateSet the Start Time Setting the Start Date Setting the Start Time or Stop TimeTo change the Start Date Defining the Start Action or Stop Action Defining the Repeat Setting„ Daily „ Weekly Changing the IR / RF Settings Using the RC9500 with Radio FrequencyReference Choosing Another Channel SoftwarePC Requirements Internet FunCleaning the RC9500 Maintaining Your RC9500Important Notice General Problems TroubleshootingProgramming Problems Recharging Problems Frequently Asked Questions How do I calibrate the Touch Screen? Overview of Symbols Overview of Symbols Display SpecificationsIndex VolumeDSS ADD Operating Other Service and Support Service and SupportUpdates and New Products Memo Japan