Introduction
About the Remote Control
Loading the Batteries
A Open the battery | B Insert two “AA” (R6) |
compartment cover. | batteries, with each one |
| oriented correctly. |
CClose the cover.
Cautions on Batteries
•Use “AA” (R6) batteries in this remote control.
•Replace the batteries with new ones approximately once a year, though this depends on the frequency with which the remote control is used.
•If the remote control does not operate within a close proximity of the main unit, replace the batteries with new ones, even if less than a year has passed.
•The included batteries serve only for verifying operation. Replace them with new batteries as soon as possible.
•When inserting the batteries, be careful to do so in the proper direction, following the 
and 
marks in the remote control’s battery compartment.
•To prevent damage or battery fluid leakage:
-Do not mix a new battery with an old one.
-Do not mix two different types of batteries such as alkaline and manganese.
-Do not
•Remove the batteries when not planning to use the remote control for a long period of time.
•If the batteries should leak, carefully wipe off the fluid from the inside of the battery compartment, then insert new batteries.
Using a Remote Control
Keep in mind the following when using the remote control:
•Make sure that there are no obstacles between the remote control and infrared sensor window on the unit.
•Remote operation may become unreliable if strong sunlight or fluorescent light is shining on infrared sensor window of the unit.
•Remote control for different devices can interfere with each other. Avoid using remote control for other equipment located close to the unit.
•Replace the batteries when you notice a fall off in the operating range of the remote control.
•The maximum operable ranges from the unit are as follows.
- Line of sight: | approx. 16 feet (5m) |
-Either side of the center: approx. 16 feet (5m) within 30°
| 30° | 30° |
|
16 feet (5m) 30° | 16 feet (5m) | 16 feet (5m) 30° | |
Changing the Signal Code of a Remote Control
To avoid the other Marantz’s BD players responding the remote signal of this unit, you can change the signal code of the remote control. If the signal code of the remote control does not match to the signal code of the unit, you cannot control the unit with the remote control.
Change the signal code of the unit
1)In stop mode, press [SETUP].
2)Use [Y / Z] to select 
, then press [ENTER].
3)Use [Y / Z] to select 
, then press [ENTER].
4)Use [U / V] to select “Remote Control Setting”.
5)Press [ENTER] to select “BD1” or “BD2”.
ENGLISH |
Introduction |
|
• At this point the new signal code of the unit is effective. Please |
|
| |
change the signal code of the remote control to match to the | Introduction |
Press and hold down both C and [1] on the remote control for at | |
signal code of the unit with following procedure. |
|
| Change the signal code of the remote control |
| |
| Set to “BD1”: |
| |
| least five seconds. |
| |
| Set to “BD2”: |
| |
|
| ||
| Press and hold down both C and [2] on the remote control for at | Connections | |
| least five seconds. | ||
|
| ||
| • If the signal code does not match, the signal code of the remote |
| |
| control will be displayed on the front panel display. |
| |
| • The default setting and the setting after you change the |
| |
| batteries is “BD1”. |
| |
| • If the code setting on the unit is “BD1”, and the setting on the |
| |
| remote control is “BD2”, “BD2” is shown on the front panel |
| |
| display. | Playback | |
|
|
| |
| T Button illustrations used in this manual for operation |
| |
|
|
| |
| explanation are for the Remote Control Unit. |
|
|
| You can operate the unit using the button of the same |
|
|
| name on the front panel of the unit. |
|
|
|
|
|
|
|
|
| Function Setup |
|
|
|
|
|
|
| Others |
Others |
|
Power Saving | On |
Remote Control Setting | BD1 |
HDMI CEC | On |
Media Select | Disc |
Network Connection | Enable(Easy) |
Network Update |
|
6) Press [SETUP] to exit.
6
ENGLISH