FUNAI CSV205DT Quick Use Guide, Connections, Installing the Batteries, For the Remote Control

1 Connections

Please refer to “Basic TV Connection” on the front page befor you use this unit.

RF Output Channel

If channel 3 is already occupied for broadcasting,

1)Set your TV to channel 4.

2)Insert a pre-recorded tape into this unit.

Quick Use Guide

4 Turn on the unit for the first time

VCR

VCR

1

Turn on the TV and set it to channel 3.

•If channel 3 is already occupied for broadcasting, see“RF Output Channel” section.

5	Clock Setup
		VCR
	VCR
1	MENU	- M E N U -
		TIMER PROGRAMMING
		AUTO REPEAT [OFF]
		CHANNEL SET UP
		B CLOCK SET
		LANGUAGE SELECT

• If the clock is not set, the

3)Press [SOURCE] on the unit so that the VCR OUTPUT light is lit.

•If noise appears on the TV screen, press [VCR/TV] on the remote control.

4)Press [PLAY B] once.

2 STANDBY-ON Remote Control TV Screen

or

CLOCK SET screen appears when you press [MENU]. In this case, go to step 2).

5)After a few seconds, hold [PLAY B] on the unit for 3 seconds.

•The RF output channel will change to channel 4 from channel 3 and you will see a playback picture.

•When a picture does not appear on the TV screen, repeat step 4).

6)Press [STOP C] to stop playback.

2	Installing the Batteries
	for the Remote Control
1	2	3

	LANGUAGE SELECT
	B ENGLISH	[ON]
	FRANCAIS
or	ESPAÑOL

3	CH 01
	AUTO SET UP

2	CLOCK SET
MONTH DAY		YEAR
1 0	/ – –	– – – –
or
HOUR MINUTE		AM/PM
– –	: – –	– –
Select the current month.
3	CLOCK SET
MONTH DAY		YEAR
1 0	/ 0 3	– – – –
or
HOUR MINUTE		AM/PM
– –	: – –	– –

Select the current day.

✄

3	VCR/DVD Switching
					STANDBY-ON			OPEN/CLOSE
						SPEED	AUDIO	/EJECT
y				X Y
					1	2	3
								SKIP/CH.
					4	5	6
								VCR/TV
				VCR button	7	8	9
						0	+10	SLOW
					DISPLAY	VCR	DVD	PAUSE
				DVD button
				VCR OUTPUT		PLAY
VCR		DVD				STOP
				light	RECORD
				DVD OUTPUT	MENU		ENTER
	X Y				SETUP	TOP MENU		RETURN
			H	light	MODE	ZOOM	MODE	C. RESET
							SEARCH	CLEAR/
					SUBTITLE	ANGLE	REPEAT	A-B
					T-SET
	SOURCE			SOURCE button

VCR MODE

Press [VCR] on the remote control. (Verify that the VCR OUTPUT light is lit.)

DVD MODE

Press [DVD] on the remote control. (Verify that the DVD OUTPUT light is lit.)

Hint

•Pressing only [SOURCE] on the front panel DOES NOT switch the mode of the remote control. You MUST select the cor-

rect mode on the remote control.

Do you connect the cable from the cable box or the satellite box to the unit’s ANT-IN jack?

YES

Yes Press [MENU]

to exit.

NO

No Please wait for a few minutes.

After scanning...

•The tuner stops on the lowest memorized channel.

•You can select only the channels memo- rized in this unit by using

[SKIP/CH. G/K H/L] (or [CHANNEL K/L]).

•If “AUTO SET UP” appears on the TV screen again, check the cable connections. Then, press [B] once again.

4		CLOCK SET
	MONTH DAY		YEAR
or	1 0	/ 0 3	2 0 0 5
	HOUR MINUTE		AM/PM
	– –	: – –	– –
	Select the current year.
5		CLOCK SET
	MONTH DAY		YEAR
or	1 0	/ 0 3 MON 2 0 0 5
	HOUR MINUTE		AM/PM
	0 5	: – –	– –
	Select the current hour.
6		CLOCK SET
	MONTH DAY		YEAR
or	1 0	/ 0 3 MON 2 0 0 5
	HOUR MINUTE		AM/PM
	0 5	: 4 0	– –
	Select the current minute.
7		CLOCK SET
	MONTH DAY		YEAR
or	1 0	/ 0 3 MON 2 0 0 5
	HOUR MINUTE		AM/PM
	0 5	: 4 0	P M AM
			B PM

Select “AM” or “PM”.

8To exit the CLOCK SET screen

– 27 – EN