ICP DAS USA 7000 PCI-7520AR Pin Assignment and Specification, Terminal Wire RS-485 Wire RS-422

Page 20

2.5 PCI-7520AR Pin Assignment and Specification:

CN1

 

 

 

1

 

 

 

6

 

 

 

2

RXD

 

 

7

TXD

 

 

3

 

 

8

 

 

 

4

 

 

 

9

GND

 

 

5

 

 

DB9M FEMALE

 

 

 

CN2

 

CN2

RX+

5

 

5

9

 

9

RX-

4

 

4

RX+

8

 

8

RX-

3

D-

3

 

7

7

TX-

2

D+

2

TX+

6

D-

6

TX-

1

D+

1

TX+

DB9S MALE

 

DB9S MALE

 

RS-485 ( D+, D- )

RS-422 ( RX+, RX-, TX+, TX- )

CON2: RS-485/422 DB9 Male Connector

Terminal

2-wire RS-485

4-wire RS-422

1

DATA+

TX+

2

 

 

3

Not Connect

4

Not Connect

RX+

5

 

 

6

DATA-

TX-

7

 

 

8

Not Connect

RX-

9

 

 

 

 

 

The PCI-7520AR is exactly the same as 7520AR except for the PCI interface. It is designed for easy installation.

7000 Bus Converter User Manual (version 1.2,Feb/2003, 7PH-006-10) ---------------

20

Image 20
Contents 7000 Series Bus Converter Common Features of the 7000 Series Dimension7520 Pin Assignment and Specifications Block Diagram 7000 series overview7510 7513PC Networking Applications RS-232 Devices Network Quick Starting the 7000 SeriesIntroduction Group 10 Power supply module ACE-540A 24V/2A power supply Page Page Page Page Back View Stack Mounting Din Rail Mounting 7520/A/R/AR, PCI-7520AR, PCISA-7520R Isolation voltage3 I-7520 is designed Termination resistor 120 Ohm on board Remove resistorI-7520R Pin Assignment and Specifications 7520R RS-232 to RS-485 ConverterI-7520A Pin Assignment and Specifications 7520A RS-232 to RS-422/485 ConverterDefault sitting Ohm on board JP1JP3 I-7520AR Pin Assignment and Specifications 7520AR RS-232 to RS-422/485 ConverterNot Connect PCI-7520AR Pin Assignment and SpecificationTerminal Wire RS-485 Wire RS-422 PCISA-7520R Pin Assignment and Specification Terminal Wire RS-4857000 Host Computer 7520 Page Therefore the Host PC/PLC is common ground with NetworkPower Ground with Host PC/PLC for Uses the same DCHost PC/PLC If there is high voltageConfiguration B 7560 / I-7561 I-7560 Pin Assignment and Specifications IntroductionI-7560 System Network Configuration Block Diagram 3 I-7560 Driver Installation Installing the DevicePage Page Page Page Page Page Page I-7561 Pin Assignment and Specifications SpecificationsPage Set Type Channels RS-485 4 I-7561 is designed Termination resistor 120 Ohm on boardJP3 Page Page Page Page Page Page Page Page Page Page Page Page I-7563 Pin Assignment and Specifications 7563Page Page Page Page Page Page Page Page Page I-7551 Pin Assignment and Specifications RS-232 TxD, RxD, CTS, RTS, GND or TxD, RxD, DCD, DTR, GNDPage 7510 / I-7510A / I-7510AR I-7510A Pin Assignment and Specifications 7510A RS-485/RS-422 RepeaterI-7510AR Pin Assignment and Specifications 7510ARPage 7513 Page Page RS-485 Networking This is the third function GND Page PLC Networking Applications RS2PC Networking Applications RS-485 Series 7520 Host PC RS-232 device Find Status of Unknown Module Wire connection Refer to Sec Quick Starting the 7000 SeriesChanging Module Address Wire connection Refer to Sec Press $02FEnterChanging Baud Rate Wire connection Refer to Sec Checksum Enable/Disable Wire connection Refer to Sec Press $012Enter Receive=!01080640B1Checksum=0