ICP DAS USA 7000 user manual 3 I-7560 Driver Installation, Installing the Device

Page 30

3.1.3 I-7560 Driver Installation

Installing the Device

This section will guide you on how to install the I-7560 USB to RS-232 converter under Windows XP, Windows 2000, Windows ME, and Windows 98 operating systems. (No support for WinNT). Download driver files from

1.Package CD, \Napdos\7000\756x\7560

2.ftp://ftp.icpdas.com/pub/cd/8000cd/napdos/7000/756x/7560

The following steps will show how to install the device under Windows 2000. Basically, the procedures are also somewhat the same for other Windows operating systems.

1.Power on your computer and boot to Windows.

2.Locate the USB port of your computer and plug in the I-7560.

3.Windows will detect the new device and will initiate the Found New Hardware Wizard prompting you to install the software for the detected USB Device. Select to install from a list or specific location. Click Next to continue.

7000 Bus Converter User Manual (version 1.2,Feb/2003, 7PH-006-10) ---------------

30

Image 30

Contents 7000 Series Bus Converter 7520 Pin Assignment and Specifications Block Diagram Common Features of the 7000 SeriesDimension 7000 series overview7510 7513PC Networking Applications RS-232 Devices Network Quick Starting the 7000 SeriesIntroduction Group 10 Power supply module ACE-540A 24V/2A power supply Page Page Page Page Back View Stack Mounting Din Rail Mounting 7520/A/R/AR, PCI-7520AR, PCISA-7520R Isolation voltage3 I-7520 is designed Termination resistor 120 Ohm on board Remove resistorI-7520R Pin Assignment and Specifications 7520R RS-232 to RS-485 ConverterI-7520A Pin Assignment and Specifications 7520A RS-232 to RS-422/485 ConverterDefault sitting Ohm on board JP1JP3 I-7520AR Pin Assignment and Specifications 7520AR RS-232 to RS-422/485 ConverterPCI-7520AR Pin Assignment and Specification Terminal Wire RS-485 Wire RS-422Not Connect PCISA-7520R Pin Assignment and Specification Terminal Wire RS-4857000 Host Computer 7520 Page Therefore the Host PC/PLC is common ground with NetworkHost PC/PLC Power Ground with Host PC/PLC forUses the same DC If there is high voltageConfiguration B 7560 / I-7561 I-7560 Pin Assignment and Specifications IntroductionI-7560 System Network Configuration Block Diagram 3 I-7560 Driver Installation Installing the DevicePage Page Page Page Page Page Page I-7561 Pin Assignment and Specifications SpecificationsPage Set Type Channels RS-485 4 I-7561 is designed Termination resistor 120 Ohm on boardJP3 Page Page Page Page Page Page Page Page Page Page Page Page I-7563 Pin Assignment and Specifications 7563Page Page Page Page Page Page Page Page Page I-7551 Pin Assignment and Specifications RS-232 TxD, RxD, CTS, RTS, GND or TxD, RxD, DCD, DTR, GNDPage 7510 / I-7510A / I-7510AR I-7510A Pin Assignment and Specifications 7510A RS-485/RS-422 RepeaterI-7510AR Pin Assignment and Specifications 7510ARPage 7513 Page Page RS-485 Networking This is the third function GND Page PLC Networking Applications RS2PC Networking Applications RS-485 Series 7520 Host PC RS-232 device Find Status of Unknown Module Wire connection Refer to Sec Quick Starting the 7000 SeriesChanging Module Address Wire connection Refer to Sec Press $02FEnterChanging Baud Rate Wire connection Refer to Sec Checksum Enable/Disable Wire connection Refer to Sec Press $012Enter Receive=!01080640B1Checksum=0