Trouble Checks, Here’s what to try

Trouble Checks

Rewind does not operate

VCR PLUS display appears

on TV instead of VCR MAIN MENU when you

press PROGNCR+ on remote.

.,. ,.,,

,.,.,

,,.

,.,,

VCR Plus+ or Timer recording not made or wrong program recorded

Clock shows incorrect time or date

*Tape already rewound.

1,.. ,,,.,..“,.,__.. ,,-,-_., ,,,.,.,, ._,,,,,,.,,,,.,,,..,,.,..,.,..-_. - ,....,. -., ,,,,- ,,_.,,.,,.,. ,,,,,, ,.,,, ,,_, ,,.,,, ,,,, ,,,,

-After VCR PLUS has been used, the VCR PLUS display will appear automatically when you press PROGNCR+ on remote. Press PROWCR+

again to display the VCR MAIN MENU.

.,., ,.., ..I,,,.,.,.,.,,_.,..,,..,.,.,,,,,.,.. .,,.,,,,,,.,,.,,.,,,,,,,,,.,.,,,,.,,,.,,, .,. ,.,, ,_,

: -	Code number for	VCR Plus+ program entered	incorrectly. See page 22.
.	VCR Plus+ setup	not done or done incorrectly.	See pages 20.21.

. Cable box was not tuned on at time recording was to begin or cable box set-up was not done correctly. See page 21.

*Power interruption. Clock area in display panel will show - - : - -.

. Check to see if time and date are cox~ect - including AM/PM.

*Program exceeded tape’s length or tape was not rewound beforehand.

:* VCR was not turned off at the time recording was to start.

. No tape in VCR, or cassette is ejected if safety tab is broken off.

. VCR ejects cassette when the end of the tape is reached during a timer

recording.

.,,,.,

*Power intenuption. Clock on the front panel will show - - : - -.

. Clock was not set accurately (check AMIPM and date).

- Time counter display appears in VCR’s display panel. Press DISPLAY on remote.

VCR makes noise when stopped	* VCR is removing tape from	heads.	This is normal. The head cylinder inside
	the VCR will continue to rotate for a few minutes after you put the VCR in
	the stop mode.	,,.,,
	,.,., .,,	,,.,,
Will not AutoPrograti active	* Check antenna connections.
channels correctly	. Check CABLE/ANT: feature	to make	sure it is properly set. See page 8.
Tape plays back in slow motion	. Press PLAY/PAUSE on VCR or PLAY on remote to return			to normal playback.
Cannot select cable channels over 69	* Cable channels over 69 can only be selected if CABLE/ANT			feature is set to
	CABLE. Details are on page8.
VCR and remote buttons will not operate VCR	: . Pro-TM Plus feature turned	on. Press and hold VCR1 (VCR2) button on
	remote for five seconds to tom Prc+Tect Plus off. HELLO appears in VCR’s
	display panel.

. ST/MONO/SAP feature must be set to STEREO to record broadcast stereo. seepage19.

:. ST/MONO/SAP feature must be set to SAF’to record SAP. See page 19.

- STEREO indicator not on. Station not broadcasting stereo.

No stereo sound during playback	* AUDIO PLAY (HIFI/MIWLINEAR) feature must be set to HIFI to hear stereo
No stereo sound during playback	sound during playback. See page 17.
	sound during playback. See page 17.
	,., ,_	,,,.,,	,,, ,,,,	,,,	,_,
Stereo audio too noisy	* Stereo signal is weak. Set ST/MONO/SAP feature to MONO.
Stereo audio too noisy	* Press one of theTRACKING buttons on the remote to minimize the noise.

,.,, ,,,,.,,,,,	,,,,	,,,,	,,.,,,	,.,	..,.

lllll I