RCA VR270 owner manual Batter3InstalLation, Battery

Page 16

Before you use the remote control unit supplied with

sour ViSR, install the batteries (instructions below). Several of the remote's buttons do the same things as buttons with the same names on the top of your VCR, and you can use whichever one is more convenient at the

moment.

The remote control has additional buttons for

controlling some of the VCR's special features, and it is

also used for setting the clock and programming the timer.

Since the remote control operates the VCR by infrared light, it is immune to electrical and sound interference. However, you must aim the remote control directly at

the VCR. There cannot be any obstructions between them.

-Batter3'InstalLation

The batteries supplied with your remote control are packed separately. Here's how to install them:

1.Turn the remote control over and remove the cover of the batter 3 compartment.

2.Insert the batteries so that their positive (+) ends contact the positive terminals in the battery'

compartment. These are marked (+) in the bottom of the compartment.

3.Replace the cover.

Remote Control

(Back View)

Battery

Compartment

/ Cover

Notes:

•Never place ans'thin_ heav_' on top of the remote control or lab" it upside-clown. This may' acci-

dentally' depress the buttons for a long time and discharge the batteries.

•Replace the batteries when the VCR fails to respond to the remote control.

•Remove the batteries from the remote control if it will not be used for a month or more. This will

prevent possible damage from battery leakage.

Location and Function of

Remote Control Buttons

POWER Button: Turns the VCR on and off. (If the

VCR is off. inserting a cassette will automatically turn it on.)

@Number Buttons (0 through 9): Select any channel (whether or not it is in the Tuner Scan List) by pressing two buttons. (Press 0 and then 8 for Channel 8.) The numbered buttons are also used for setting the clock and programming the timer.

(_ Channel • and Butlnns: Use these buttons to

select the next channel up or down programmed in the scan list.

The VCR tuner must be programmed for the Channel • and • buttons to wort:. Details are on

page 12.

PROGRAM Button: Used to set the clock and program the timer with use of the on-screen display on )'our TV.

® PAUSE Button: Pressing the PAUSE button during recording stops the tape so that nothing will be recorded. When you press the PA USE button again, recording resumes immediately.

Pressing PA USE during playback produces a stop- action picture, and pressing it again resumes normal playback. Details are on page 20.

® CLEAR Button: Used to clear incorrect information when programming the timer. Also used to clear a timer program or to reset the Tape Counter to "0000".

@DISPLAY Button: Controls on-screen displays.

•Press once to bring normal displays to TV screen.

•Press twice to display Tape Counter and turn on counter memory.

•Press three times to remove all displays lrom TV screen.

14

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Nell VideoCassette Recorder Dealer Model VR270 Serial Number Using This Manual On-Screen Remote Timer Programming-With RCAs CompactDesi.m-State-of-theminiaturization-artPage Location TYPtCALBasic Cable-TV Connections Back of VCRThis Cab,eVHF VCR to Back Co*i=Back Back of TVCo.,,aI Igp.W..dNot CorDSwitch ConnectionsOperating Instructions Direct Video and Audio ConnectionsTo UHF Antenna To TVs Video Used Only if You Have Home UHF AntennaBasic Operating Controls and Displays Inserting and Removing CassettesUTO PROG/ADD/ERASE Buttons These AreaErasing Channels from the Scan List Programming Active Channels into VCRs- TunerAdding Channels to the Scan List Simplified Installation Checklist Setting Your IV to the VCR ChannelUsing the TV VCR Button Press Power to turn on VCRBatter3InstalLation BatteryNumber Buttons PLAYButton Stop ButtonButton Buon121 Display prompts you to select AM orMaking a Recording Playing It BackOperating Notes Turn on PressLEt StOO,UE¢ ADD/ERASE or Tracking Buttons AppearTurned Jacks BackPause During Recording Pause for Stop-Action Playback=Picture Search Tracking ControlOn-Screen Display You can proam the timer to do the-- following Simplified Programming InstructionsTurn on VCR Press Program on the remote hand unitDisplay will show Start Date Clearing a Timer ProgramFollowed by the current or next date and day Stopping a Timer Recording in Proess Timer Recording From the Line InputStep Cassette Care and Storage Recording SpeedReading Quick 7onent Recording Tion On when you Record Normal ViewingRecording With Off Recording Viewing the Same ProgramSelect Desired tape Indicator will light Speed Make sure indicator is onRecording and Viewing Different Programs Basic PlaybackSimplified Operating Instructions Dub TapesYounormallyuse Light WillPress to record Play, Record, Rewind,Turns the Tape CounterI Press during Playback to displayUsed when setting the clock and programming the timer Places VCR in Pause mode whenTimer. Also resets tape counter Moder Press again to release pause Press to turn off VCRCleaning Dusting attachment of ,our \acuum cleanerTransformers ConnectorsAdapters Number SpecialPLA Y Button Timer Programming TimerArrangements TimeMarcas Registraclas Job A-58530 E72t Thomson Consumer Electronics, IncPart Number 2826
Top Page Image Contents