Pioneer DVR-433H-K Additional information about the TV system settings, About Ntsc on PAL TV

Page 99

The Initial Setup menu

13

Additional information about the TV system settings

About the input line system

This recorder is compatible with PAL, SECAM, 3.58 NTSC and PAL-60 TV systems. The Input Line System and Input Colour System settings determine how the recorder treats incoming video signals from an external input or the built-in TV tuner.

Please note the following points when changing the input line system:

•When the current input is a built-in tuner channel preset, changing the input line system will usually also affect the input line system of the AV2/AUTO START REC (INPUT 1/DECODER) input. However if the AV2/L1 In setting is set to Decoder, then the L2 input is affected instead.

•If, when the Input Line System setting is changed, the screen goes blank (due to incompatibility with your TV), you can switch back by pressing and holding the

front panel button then pressing OPEN/CLOSE (front panel) while the recorder is stopped.

•When you switch the Input Line System setting the Copy List is erased. If you switch the setting using the button and OPEN/CLOSE buttons as described above, there is no confirmation, so please use with

care.

•You can’t mix recordings of different TV line systems on the same disc.

•When you change this setting, the Input Colour System setting also changes (see below).

About NTSC on PAL TV

Depending on the Input Line System setting and the NTSC on PAL TV setting, the signal format output when the recorder is stopped varies as shown in the table below.

Input Line System

NTSC on PAL

Output when

TV

stopped

 

 

 

 

625 System

Off

PAL

 

 

 

 

On

PAL

 

 

 

525 System

Off

NTSC

 

 

 

 

On

PAL–60

 

 

 

About the input colour system

The available options of the Input Colour System setting depend on the Input Line System setting. The table below shows the different options available.

Input Line System

Built-in tuner

External input

625 System

Auto

Auto

 

 

 

 

PAL

PAL

 

 

 

 

SECAM

SECAM

 

 

 

525 System

n/a

Auto

 

 

 

 

 

3.58 NTSC

 

 

 

 

 

PAL–60

 

 

 

Additional information about component video output

If you switch the Component Video Out setting to Progressive when using a TV that is not compatible with progressive-scan video, you will not be able to see anything displayed on your TV. If this happens, press and hold the button on the front panel, then press

. This will set the recorder’s video output back to Interlace.

Compatibility of this unit with progressive-scan TVs

Consumers should note that not all high-definition television sets are fully compatible with this product and may cause artifacts to be displayed in the picture. In case of 525 progressive scan picture problems, it is recommended that the user switch the connection to the ‘standard definition’ output (Interlace). If there are questions regarding our TV set compatibility with this model, please contact our customer service center.

This recorder is compatible with the following Pioneer displays and monitors

Plasma display

•PDP-503HDE, PDP-433HDE, PDP-434HDE, PDP-504HDE, PDP- 435XDE, PDP-435HDE, PDP-435FDE, PDP-505XDE, PDP- 505HDE, PDP-615EX

99

En

Page 98 Page 100
Image 99
Page 98 Page 100
Contents DVR-433H-SDVR-433H-K Risk of Electric Shock Do not Open Ventilation Caution Operating EnvironmentContents Additional information Disc Setup menuVideo/Audio Adjust menu Initial Setup menuFeatures Before you startBefore you start Chapter Before you start Putting the batteries in the remote control Using the remote controlBefore you start What’s in the box Compressed audio compatibility General disc compatibilityDVD-R/RW compatibility CD-R/RW compatibilityWMA Windows Media Audio compatibility Jpeg file compatibilityPC-created disc compatibility Optimizing HDD performance About the internal hard disk driveFront panel connections Connecting upConnecting up Chapter Rear panel connectionsConnecting up Extra features for use with compatible TVs Connecting up Easy connections Connect the Video Output jack to a video input on your TV Connecting up Using other types of audio/video outputUsing the supplied audio/video cable Using the S-video or component video outputConnect RF antenna cables as shown This enables you to watch and record TV channelsThis enables you to watch discs This enables you to record scrambled TV channelsScart AV Connecting up Connecting an external decoder boxDecoder Wall outlet This enables you to listen to multichannel surround sound Connecting up Connecting to an AV amplifier/receiverConnecting up Connecting other AV sources PluggingAfter checking all the connections, plug in the recorder Controls and displays Controls and displays ChapterFront panel Controls and displays Remote control HelpClear REC Controls and displaysShift Stop RECEP / SEP Controls and displays DisplayNtsc LP / SLPEnter Switching on and setting upGetting started Getting started ChapterGetting started Is your TV compatible with progressive scan video? Other settings you can makeSelecting the hard disk or DVD for playback and recording Select the TV screen type, ‘Wide 169’ or ‘Standard 43’Press REC to start recording When you want to stop recording, pressGetting started Making your first recording Playing back your recordingNicam Getting started Using the built-in TV tunerChanging TV channels Changing audio channelsSwitching between TV and DVD To stop playback, press Press STANDBY/ON to switch onGetting started Basic playback If playing video from the HDD, skip to belowPlaying from the HDD Playing DVD discsPlaying Video CD/Super VCDs Playing CDs and WMA/MP3 discsHome menu options Getting started Using the Home MenuDisplaying disc information on- screen Home MenuStop display HDD and removable disc activity displayRecording display Play displayAbout DVD recording HDD Video mode compatibilityRecording Recording ChapterRecording equipment and copyright Recording Recording time and picture qualityRestrictions on video recording Recorded audioFront panel display shows the channel number Recording Setting the picture quality/recording timeBasic recording from the TV XP High quality SP Standard play LP Long playRecording Direct recording from TVTo stop the recording, press Stop REC Recording Setting a timer recording Press Enter to set the start time Easy Timer RecordingSet the TV channel and recording quality Current time Recording start timeConfirm that the settings are correct If the channel number isnt displayed, useSelect ‘Store Program’ to finish Press ’VIDEO Plus+ Shift + MENU’ Video Plus+ programming with the power offSetting a manual timer recording Press Timer REC to display the Timer Recording screenTo exit the timer recording screen, press Home Menu Tip Enter the timer recording settingsExtending a timer recording in progress Editing a timer programDeleting a timer program Skipping a regular timer programUnlock Timer recording FAQCanceling and stopping a timer recording in progress You can’t enter a timer program if the clock isn’t setPlayback Component See Connecting up for connection optionsAutomatic recording from a satellite tuner Set up the recorderPress REC when you’re ready to start recording See Audio In Settings on page 94 for more on these settingsRecording Recording from a DV camcorder Also, set the camcorder to VTR modePress Enter Playing your recordings on other DVD playersFinalizing a disc UseIt takes about 30 seconds to initialize the disc Press Home Menu and select ‘Disc Setup’ Select ‘Finalize’Press Home Menu and select ‘Disc Setup’ Select ‘Initialize’ Initializing a recordable DVD discNavigating discs and the HDD PlaybackPlayback Chapter IntroductionPlayback Using the Disc Navigator to browse the contents of a discSelect what you want to play Using the Disc Navigator with playback-only discsGenre Display all genres or just a selected genre PressScan Playback Scanning discsPlaying in slow motion Slow 1/4Play Mode menu Search ModePlayback Frame advance/frame reverse Repeat Repeat playPlayed over and over.1 Program play Repeat to build up a program listTo play the program list, press Other Program play functions Displaying and switching subtitlesAudio channels currently playing are indicated on- screen Playback Switching DVD soundtracksSwitching audio channels Stereo Stereo default Left channel only Right channel onlyTo switch the camera angle, press Angle Shift + Switching camera anglesRestrictions on copying Copying and back-upCopying and back-up Chapter One Touch CopyCopying from HDD to DVD Using Copy ListsCanceling One Touch Copy Copying and back-upSelect VR mode or Video mode for the copy Select ‘HDD DVD’If you select Use Existing Copy List, skip to below Select ‘Start Copy’ to start copying Select ‘Next’ to move on to the Title Edit screenCopying from DVD to HDD EraseTitle Name Highlight the title you want to move and press Erase SectionMove Select the type of editChapter Edit PreviewDivide CombineSet Thumbnail Recording ModeUsing disc back-up BilingualOption Copying and back-up Disc Navigator screen Playback will automatically stop when you do thisEditing Editing ChapterHDD genres Editing Command menu panel optionsVideo mode VR mode Original Play List Editing accuracyPlay Select ‘Create’ from the command menu panelEditing CreateUsing the remote key shortcuts to input a name Key CharactersVideo Select ‘Exit’ to return to the Edit screen You can also use the CM Skip Shift + ButtonsSelect ‘Exit’ to get back to the main Disc Navigator screen Use this command to assign a genre to a title Set GenreLock Multi-Mode Genre NameFor example, select Erase to erase all the marked titles Select ‘Next’ from the command menu panelSelect ‘Undo’ from the command menu panel UndoPress to starts CD playback Press ONE Touch Copy Using the JukeboxUsing the Jukebox Chapter Copying CDs to the HDDUsing the Jukebox Playing music from the Jukebox Editing Jukebox albumsSelecting a track from an album to play Genre Using the JukeboxChanging the album view Display orderPhotoViewer PhotoViewer ChapterPlaying a slideshow Rotating an image PhotoViewerReloading files from a disc Zooming the imageInitialize settings Disc Setup menuDisc Setup menu Chapter Basic settingsOptimize HDD Disc Setup menuFinalize settings1 Initialize HDDChoosing a preset Video/Audio Adjust menuVideo/Audio Adjust menu Chapter Setting the picture quality for TV and external inputsVideo/Audio Adjust menu Setting the picture quality for disc playbackSelect the picture quality setting you want to adjust ‘Max’ Audio DRCSetting Options Explanation Initial Setup menuInitial Setup menu Chapter Using the Initial Setup menuInitial Setup menu RGB Mpeg PCM MpegAuto Language Language Settings OSD Language EnglishAudio Language English OtherVideo Mode On DVD-RW Auto Init VR ModeVideo Mode Video Mode OffStill Picture Field Parental Lock Set PasswordChange Password Remote Control Mode RecorderAbout Ntsc on PAL TV Additional information about the TV system settingsAdditional information about component video output About the input line systemPress Enter to confirm and exit the screen Selecting other languages for language optionsSelect ‘Other’ from the language list Select the language you wantAdditional information Chapter When viewing on a standard TV or monitorWhen viewing on a widescreen TV or monitor Additional informationMins Additional information Minimum copying timesDVD disc type Rec ModeAdditional information Troubleshooting Problem RemedyGeneral Additional information HDD Frequently asked questionsDV-related messages About DVVideo mode On HDD VR mode DVD Video mode DVD Resolution LevelAdditional information Manual recording modes Country/Area, Country/Area code, Code letter Additional information Language code listCountry/Area code list Language Language code letter, Language codeMessage Explanation/Action Message Condensation Additional information Resetting the recorderCleaning the pickup lens Handling discsAdditional information Hints on installation Moving the recorderDon’t Additional information Glossary PCM Pulse Code Modulation Mpeg audioMpeg video Optical digital outputInput/Output Additional information SpecificationsTimer TunerLINK/IEEE 1394 standard Supplied accessoriesAV Connectors 21-pin connector assignment Component video outputError messages 106 recording from Language audio 61, 96 code list 108 DVD menuIndex Ntsc Timer recording 41-47 TitleVRB1379-A Pioneer Corporation
Top Page Image Contents