Pioneer PRO-1000HDI Operations, Selecting an Input Source, Before you begin, make sure you have

Page 26

Operations

Selecting an Input Source

This section explains the basic operation of this unit. Outlined on the following pages is how to turn the main power on and off, put this unit in the operation or standby mode and how to select connected components.

Before you begin, make sure you have:

•Made connections between this unit and AV components or personal computer as described in the section “Installation and Connections” starting on page 8.

•Set up the on-screen menu to input signals from components connected to INPUT1 and INPUT2 as described in the section “Setting Up the System” on page 18.

If no connections are made to these terminals, on-screen setup is not necessary.

2,5

2,5

3

3

4

Main Unit Operating

Remote Control Unit

Panel

 

1Switch the main power switch on the main unit to the on position to turn the main power on.

The STANDBY/ON indicator lights red.

2Press STANDBY/ON to put this unit in the operation mode.

The STANDBY/ON indicator turns green.

22

3Press INPUT on the remote control unit or the main unit to select the input.

Input changes each time the main unit’s INPUT is

pressed as follows.

 

3 INPUT1

3 INPUT2

3 INPUT3

 

 

 

 

 

 

 

 

 

 

 

 

 

INPUT5 2

 

INPUT4 2

 

 

 

 

 

 

•When the menu screen is displayed, changing the signal input will cause the menu screen to turn off.

•If the input computer signal is not supported by the display, the following message will be displayed:

I N P U T 1

CA U T I O N

UN S UP P O RT E D S I G N AL

f H : 7 7 . 1 k H z

f V : 8 5 . 0 H z 1 1 5 2 X 8 6 4

F U L L

I N P U T 1

CA U T I O N

OU T OF R AN G E

f H : 7 5 . 7 k H z

f V : 1 2 0 . 0 H z

– – – –

F U L L

4Use VOLUME +/– on the remote control unit to adjust the volume.

If no audio connections are made to this unit, this step is not necessary.

5When viewing is finished, press STANDBY/ON to put the unit in standby mode.

The STANDBY/ON indicator will blink and then remain lit (red) indicating that the standby mode is engaged. Operation is not possible while the STANDBY/ON indicator is blinking (red).

6Switch MAIN POWER on the main unit to the off position to turn the main power off.

The STANDBY/ON indicator may continue to light for a short while even after the main power is turned off. This is a result of residual electric load impressed on the circuitry, and the light will turn off presently.

CAUTION

Please do not leave the same picture displayed on the screen for a long time. Doing so may cause a phenomenon known as “screen burn” which leaves a ghost, or residual, image of the picture on the screen.

PRO-1000HDI / PRO-800HDI

Page 25 Page 27
Image 26
Page 25 Page 27
Contents PRO-1000HDIPRO-800HDI Safety Precautions Wash hands after handlingSafety Precautions NEC SectionIii Contents About operations in this manual How to Use This ManualBefore Proceeding Screen Displays÷ Warranty Remote control unitCleaning cloth for wiping front panel AA R6 batteries xMain unit Part Names and FunctionsMain Unit Operation panel on the main unitWhen handling the remote control unit Remote Control UnitInserting the batteries Remote control unit Operating range of the remote control unit Connection PanelPart Names and Functions Audio Input Stereo mini jack $ Main power switchIllustration depicts Audio Output Stereo mini jackInstallation and Connections Installation of the UnitConnection to INPUT1 and INPUT2 About the Input Connectors on thisUnit Connection to AV componentsConnection of G on Sync analog RGB source Connection of composite Sync analog RGB SourceConnection of separate Sync analog RGB Source When connecting to Output INPUT1Connection to a personal computer To an external monitor75Ω Ô2.kΩ2 Connection to INPUT5 Connection to INPUT3Connection to INPUT4 AV componentAudio Connections Connecting the speakersAbout DTV Set Top Box Connection Making connections to the audio inputs on this unitAudio connection for component connected to INPUT3Power Cord Connection Control Cord ConnectionTo remove speed clamps How to Route CablesTo attach the speed clamps to the main unit Illustration depicts PRO-1000HDImodelSetup after Connection INPUT1 Setting Up the SystemSetting the Screen Mode/Input Signal Format When inputting a computer signalClamp Position setup Setup of Clamp PositionPress SET to select the desired Video Signal setting Setup after Connection INPUT5Press 5/∞ to select Video Signal Press SET to select the desired Audio Select setting Press 5/∞ to select Signal RangePress SET to select the desired Signal Range setting Press 5/∞ to select Audio SelectSelecting an Input Source Press STANDBY/ON to put this unit in the operation modeOperations Before you begin, make sure you haveTo mute the sound To adjust the volumeTo confirm display settings Automatic screen size Screen Size SelectionChanging the screen size Moving the screen position upward or downwardArea 1 display range Area 2 display range Partial Image EnlargementArea 3 display range When the setup is finished, press Menu to exit Menu screen Automatic Power OFFTo return to operating mode All other casesTo reset Picture mode settings to the default Display Panel AdjustmentsAdjusting the Picture Quality Press 2/3 to select Screen Adjusting the Image Position and Clock Automatic AdjustmentScreen mode adjustment items Press 2/3 to carry out the adjustment To reset Screen mode settings to the defaultWhen video signal input is selected Use 5/∞ for the adjustments of V.POSITIONPress SET to select Input Label Other OperationsRewriting the Input Display Press Menu to return to the normal display screenOther Changing the Color TemperatureReducing Video Noise Digital NR Press 5/∞ to select 3D Y/C Mode Setting the PureCinema modeViewing a Fast Moving Picture 3D Y/C Mode Press SET to set the mode to MotionPower Control Function Viewing in a Bright LocationPress 5/∞ to select Auto Function Factory default setting is OFF. Each time SET isAudio Output Audio OUT Press SET to select Input 1 or InputAbout the self diagnosis mode CleaningTroubleshooting Additional InformationProblem Possible Solution General problemsProblems commonly mistaken as breakdown Protection function STANDBY/ON indicatorAbout the plasma panel’s Panel sticking and after-image lagGeneral PRO-1000HDI SpecificationsAccessories General PRO-800HDINot available PC signal compatibilty table INPUT1, INPUT2Supplement 1 -1/2 PRO-1000HDI Refresh rate Screen size Dot x line RemarksRefresh rate Screen size Dot x line Supplement Video signal compatibilty table INPUT1, INPUT2Digital signal compatibilty table INPUT5 Explanation of Terms Video signalComponent video signal Aspect ratioAdditional Information TSZZF/03I00000
Top Page Image Contents