Pioneer PRO-1000HDI manual Partial Image Enlargement, Area 3 display range

Page 29

	Operations
	2 Press 5/∞/2/3 as required to select the desired

Partial Image Enlargement
(POINT ZOOM)	screen area (AREA 1 to AREA 9).
(POINT ZOOM)

This display allows any one of nine screen areas (AREA 1 to AREA 9) to be selected and enlarged to x1.5, x2, x3, or x4. When performing point zoom enlargement, the direction buttons (5/∞/2/3) can be used to move the enlarged portion up-down and right-left.

Notes

÷The POINT ZOOM function is supported only when the input signal is from a computer.

÷Whenever POINT ZOOM is selected, the screen size automatically changes to FULL.

1Press the remote control unit’s POINT ZOOM.

3Press SET to select the zoom ratio.

Pressing SET repeatedly changes the zoom ratio in the following order:

	3 x 1.5		3 x 2.0
	3 x 1.5		3 x 2.0
	x 4.0 2		x 3.0 2
	x 4.0 2		x 3.0 2

÷When the zoom ratio is changed, the screen image is enlarged based on the screen center.

÷5/∞/2/3 can be used to move the enlarged portion up-down and right-left.

÷If no operation is undertaken for three seconds or more, the display screen will disappear.

SET or 5/∞/2/3 can be pressed again if desired to change the zoom ratio or display position.

4Press the remote control unit’s POINT ZOOM once again to cancel the point zoom operation.

The point zoom function will also be canceled whenever the input signal changes, the menu screen is displayed, or the INPUT changes.

Operations

SELECT

P.ZOOM

EXIT

SET

ZOOM

AREA 3 display range

AREA 1 display range

AREA 2 display range

AREA 1

AREA 2

AREA 3

x 4.0

x 3.0

x 4.0

x 3.0

x 3.0

x 4.0

x 2.0

x 2.0

x 2.0

x 1.5

x 1.5

x 1.5

AREA 4 display range

AREA 4
x 4.0	x 3.0
	x 3.0

x2.0

x1.5

AREA 5 display range

AREA 6 display range

AREA 5

AREA 6

x 4.0

x 3.0

x 3.0

x 4.0

x 2.0

x 2.0

x 1.5

x 1.5

AREA 7 display range

AREA 8 display range

AREA 9 display range

AREA 7
x 4.0	x 3.0
	x 3.0

x2.0

x1.5

AREA 8
x 4.0	x 3.0
	x 3.0

x2.0

x1.5


		AREA 9
x 3.0		x 4.0

x2.0

x1.5

25

PRO-1000HDI / PRO-800HDI

Image 29

Contents PRO-1000HDIPRO-800HDI Wash hands after handling Safety PrecautionsNEC Section Safety PrecautionsIii Contents Before Proceeding How to Use This ManualAbout operations in this manual Screen DisplaysCleaning cloth for wiping front panel Remote control unit÷ Warranty AA R6 batteries xMain Unit Part Names and FunctionsMain unit Operation panel on the main unitWhen handling the remote control unit Remote Control UnitInserting the batteries Remote control unit Connection Panel Operating range of the remote control unitIllustration depicts $ Main power switchPart Names and Functions Audio Input Stereo mini jack Audio Output Stereo mini jackInstallation of the Unit Installation and ConnectionsUnit About the Input Connectors on thisConnection to INPUT1 and INPUT2 Connection to AV componentsConnection of composite Sync analog RGB Source Connection of G on Sync analog RGB sourceConnection to a personal computer When connecting to Output INPUT1Connection of separate Sync analog RGB Source To an external monitor75Ω Ô2.kΩ2 Connection to INPUT4 Connection to INPUT3Connection to INPUT5 AV componentAbout DTV Set Top Box Connection Connecting the speakersAudio Connections Making connections to the audio inputs on this unitINPUT3 Audio connection for component connected toControl Cord Connection Power Cord ConnectionTo attach the speed clamps to the main unit How to Route CablesTo remove speed clamps Illustration depicts PRO-1000HDImodelSetting the Screen Mode/Input Signal Format Setting Up the SystemSetup after Connection INPUT1 When inputting a computer signalSetup of Clamp Position Clamp Position setupPress SET to select the desired Video Signal setting Setup after Connection INPUT5Press 5/∞ to select Video Signal Press SET to select the desired Signal Range setting Press 5/∞ to select Signal RangePress SET to select the desired Audio Select setting Press 5/∞ to select Audio SelectOperations Press STANDBY/ON to put this unit in the operation modeSelecting an Input Source Before you begin, make sure you haveTo mute the sound To adjust the volumeTo confirm display settings Changing the screen size Screen Size SelectionAutomatic screen size Moving the screen position upward or downwardArea 1 display range Area 2 display range Partial Image EnlargementArea 3 display range To return to operating mode Automatic Power OFFWhen the setup is finished, press Menu to exit Menu screen All other casesTo reset Picture mode settings to the default Display Panel AdjustmentsAdjusting the Picture Quality Press 2/3 to select Screen Adjusting the Image Position and Clock Automatic AdjustmentScreen mode adjustment items When video signal input is selected To reset Screen mode settings to the defaultPress 2/3 to carry out the adjustment Use 5/∞ for the adjustments of V.POSITIONRewriting the Input Display Other OperationsPress SET to select Input Label Press Menu to return to the normal display screenOther Changing the Color TemperatureReducing Video Noise Digital NR Viewing a Fast Moving Picture 3D Y/C Mode Setting the PureCinema modePress 5/∞ to select 3D Y/C Mode Press SET to set the mode to MotionViewing in a Bright Location Power Control FunctionAudio Output Audio OUT Factory default setting is OFF. Each time SET isPress 5/∞ to select Auto Function Press SET to select Input 1 or InputTroubleshooting CleaningAbout the self diagnosis mode Additional InformationProblem Possible Solution General problemsProblems commonly mistaken as breakdown About the plasma panel’s STANDBY/ON indicatorProtection function Panel sticking and after-image lagAccessories SpecificationsGeneral PRO-1000HDI General PRO-800HDISupplement 1 -1/2 PRO-1000HDI PC signal compatibilty table INPUT1, INPUT2Not available Refresh rate Screen size Dot x line RemarksRefresh rate Screen size Dot x line Supplement Video signal compatibilty table INPUT1, INPUT2Digital signal compatibilty table INPUT5 Component video signal Video signalExplanation of Terms Aspect ratioAdditional Information TSZZF/03I00000