Panasonic TH-65PF10WK PC Input Terminals connection, Signal Names for Mini D-sub 15P Connector

Page 10

Connections

PC Input Terminals connection

COMPUTER

AUDIO

PC IN

Conversion adapter
(if necessary)	Mini D-sub 15p
	Mini D-sub 15p
	RGB
	PC cable

Audio	Stereo plug

Connect a cable which matches

the audio output terminal on the computer.

Notes:

•Due to space limitations, occasionally you may have trouble connecting Mini D-sub 15P cable with ferrite core to PC input Terminal.

•Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical scanning frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.)

•The display resolution is a maximum of 1,440 × 1,080 dots when the aspect mode is set to “4:3”, and 1,920 × 1,080 dots when the aspect mode is set to “16:9”. If the display resolution exceeds these maximums, it may not be possible to show ﬁne detail with sufﬁcient clarity.

•The PC input terminals are DDC2B-compatible. If the computer being connected is not DDC2B-compatible, you will need to make setting changes to the computer at the time of connection.

•Some PC models cannot be connected to the set.

•There is no need to use an adapter for computers with DOS/V compatible Mini D-sub 15P terminal.

•The computer shown in the illustration is for example purposes only.

•Additional equipment and cables shown are not supplied with this set.

•Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the speciﬁed frequency range.

•Component Input is possible with the pin 1, 2, 3 of the Mini D-sub 15P Connector.

•Change the “Component/RGB-in select” setting in the “Setup” menu to “Component”

(when Component signal connection) or “RGB” (when RGB signal connection). (see page 41)

Signal Names for Mini D-sub 15P Connector

5 4 3 2 1

10		9		8	7	6
15	14		13	12		11

Pin Layout for PC Input Terminal

Pin No.	Signal Name	Pin No.	Signal Name	Pin No.	Signal Name
1	R (PR/CR)	6	GND (Ground)	11	NC (not connected)
2	G (Y)	7	GND (Ground)	12	SDA

3	B (PB/CB)	8	GND (Ground)	13	HD/SYNC

4	NC (not connected)	9	+5 V DC	14	VD

5	GND (Ground)	10	GND (Ground)	15	SCL

10

Image 10

Contents Model No. TH-50PF10WK High Deﬁnition Plasma DisplayOperating Instructions EnglishTable of Contents Important Safety Notice Trademark CreditsDo not place any objects on top of the Plasma Display Safety PrecautionsSetup Transport only in upright positionWhen using the Plasma Display Safety PrecautionsIf problems occur during use Clean the power cable regularly to prevent it becoming dusty Electric shocks can result if this is not doneAccessories Supply AccessoriesRemote Control Batteries Monitor terminal ConnectionsAC cord ﬁxing SeeBoard Insert Slot Equivalent of Dual ConnectionsOptional Terminal Covered HDMITerminal Board BNC Component VideoSignal Names for Mini D-sub 15P Connector PC Input Terminals connectionRS-232C Straight cable CommandSerial Terminals connection Communication parametersHdmi connection Component / RGB connectionConnecting the AC cord plug to the Plasma Display Power On / OffConnecting the plug to the Wall Outlet Power On / Off Initial selections Selecting the input signalSelecting the On-Screen Menu Language Basic Controls Remote control sensor Volume AdjustmentMain Power On / Off Switch Power Indicator Menu Screen on / OFFBasic Controls On-Screen Menu Displays On-Screen Menu Displays Mode Picture Explanation Aspect ControlsAdjusting Pos. /Size NormalisationAdjusting Pos. /Size Multi PIP Normal ViewingAdvanced PIP Options1/3Dynamic Picture AdjustmentsNormal CinemaAdvanced settings Picture AdjustmentsSound Adjustment Mute Sound AdjustmentSDI Sound Output On OffSelect the area of the image to be enlarged Digital ZoomDisplay the operation guide Select the magniﬁcation required for the enlarged displayPress to setup DAY or Present Time Present Time Setup / Set up TimerPresent Time Setup Button ForwardDisplay the Set up Timer screen Press to select Set up TimerPresent Time Setup / Set up Timer Power on Time / Power OFF TimeScreensaver For preventing image retention Mode selectionStart setting Reversal / Scroll selectionReduces screen image retention Setup of Screensaver TimeScreensaver For preventing image retention Side Panel Adjustment Addition sign Selected Input Reduces power consumptionCustomizing the Input labels CompositeSetup for Multi Display How to Setup Multi DisplaySetup for Multi Display Display Number locations for each arrangement ExamplesID Cancellation ID Remote Control FunctionID remote control button operation AI-synchronizationSet up for Portrait How to setup PortraitSet up for Portrait Viewing Area / LocationComponent / RGB-in select Setup for Input Signals3D Y/C Filter For Ntsc AV images NR / Block NR / Mosquito NR Setup for Input SignalsPress Action button Press to exit from adjust Mode Refresh RateColour system / Panasonic Auto Cinema realitySync Setting RGB sync signalPress to exit from adjust mode Press Action Button Freq. kHz / V-Freq. HzOptions Adjustments Effect AdjustmentsOptions Adjustments Options1/3Off-timer Normalization Weekly Command Timer Press to select Time / Command Shipping condition Troubleshooting Plasma Display panelCOMPONENT/RGB/PC/VIDEO input signals Video input Hdmi COMPONENT/RGB/PC/VIDEO input signalsMHz Active pixels Pixels Active lines Lines Command list of Weekly Command Timer Speciﬁcations TH-50PF10WK TH-65PF10WKMemo Memo Memo Customer’s Record