Panasonic TH-42PR10UA Maintenance, Setup, AC Power Supply Cord, If problems occur during use

Page 7

Safety Precautions / Maintenance

WARNING

Setup

Do not place the Plasma Display on sloped or unstable surfaces.

• The Plasma Display may fall off or tip over.

Do not place any objects on top of the Plasma Display.

•If water spills onto the Plasma Display or foreign objects get inside it, a short-circuit may occur which could result in fire or electric shock. If any foreign objects get inside the Plasma Display, please consult an Authorized Service Center.

Do not cover the ventilation holes.

•Doing so may cause the Plasma Display to overheat, which can cause fire or damage to the Plasma Display.

If using the pedestal (optional accessory), leave a space of 3 15/16” (10 cm) or more at the top, left and right, 2 3/8” (6 cm) or more at the bottom, and 2 3/4” (7 cm) or more at the rear. If using some other setting-up method, leave a space of 3 15/16” (10 cm) or more at the top, bottom, left and right, and 2 3/4” (7 cm) or more at the rear.

Transport only in upright position!

•Transporting the unit with its display panel facing upright or downward may cause damage to the internal circuitry.

AC Power Supply Cord

The Plasma Display is designed to operate on 110 - 127 V AC, 50/60 Hz.

Do not use any power supply cord other than that provided with this unit.

• Doing so may cause fire or electric shocks.

Securely insert the power cord plug as far as it will go.

•If the plug is not fully inserted, heat may be generated which could cause fire. If the plug is damaged or the wall socket plate is loose, they should not be used.

Do not handle the power cord plug with wet hands.

• Doing so may cause electric shocks.

Do not do anything that might damage the power cable. When disconnecting the power cable, hold the plug, not the cable.

•Do not make any modifications, place heavy objects on, place near hot objects, heat, bend, twist or forcefully pull the power cable. Doing so may cause damage to the power cable which can cause fire or electric shock. If damage to the cable is suspected, have it repaired at an Authorized Service Center.

If the Plasma Display will not be used for a long period of time, unplug the power cord from the wall outlet.

If problems occur during use

If a problem occurs (such as no picture or no sound), or if smoke or an abnormal odor is detected from the Plasma Display, unplug the power cord immediately.

•Continuous use of the Display under these conditions might cause fire or permanent damage to the unit. Have the Display evaluated at an Authorized Service Center. Services to the Display by any unauthorized personnel are strongly discouraged due to its high voltage dangerous nature.

If water or foreign objects get inside the Plasma Display, if the Plasma Display is dropped, or if the cabinet becomes damaged, disconnect the power cord plug immediately.

•A short may occur, which could cause fire. Contact an Authorized Service Center for any repairs that need to be made.

Maintenance

The front of the display panel has been specially treated. Wipe the panel surface gently using only a cleaning cloth or a soft, lint-free cloth.

•If the surface is particularly dirty, wipe with a soft, lint-free cloth which has been soaked in pure water or water in which neutral detergent has been diluted 100 times, and then wipe it evenly with a dry cloth of the same type until the surface is dry.

•Do not scratch or hit the surface of the panel with fingernails or other hard objects, otherwise the surface may become damaged. Furthermore, avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the surface may be adversely affected.

If the cabinet becomes dirty, wipe it with a soft, dry cloth.

•If the cabinet is particularly dirty, soak the cloth in water to which a small amount of neutral detergent has been added and then wring the cloth dry. Use this cloth to wipe the cabinet, and then wipe it dry with a dry cloth.

•Do not allow any detergent to come into direct contact with the surface of the Plasma Display. If water droplets get inside the unit, operating problems may result.

•Avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the cabinet surface may be adversely affected or the coating may peel off. Furthermore, do not leave it for long periods in contact with articles made from rubber or PVC.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents English Español Operating Instructions Manual de instruccionesModel No. Número de modelo Risk of Electric Shock Do not Open Important Safety Instructions Table of Contents Canadian Notice FCC CautionTrademark Credits When using the Plasma Display Safety PrecautionsIf problems occur during use MaintenanceSetup AC Power Supply CordAccessories Supplied AccessoriesCheck that you have the Accessories and items shown Optional Terminal Board Insert Slot covered ConnectionsAC cord connection see AC cord fixingPC Input Terminals connection Signal Names for Mini D-sub 15P ConnectorBasic format for control data CommandSerial Terminals connection Communication parametersConnecting the AC cord plug to the Plasma Display Power on / OFFConnecting the plug to the Wall Outlet INPUT1 INPUT2 INPUT3 PC Selecting the input signalInitial selections Selecting the On-Screen Menu LanguageOn OFF Basic ControlsDigital Zoom see Press to access Channel AdjustmentVolume Adjustment OFF Timer buttonPicture Setup Sound Advanced SettingsOn-Screen Menu Displays On Time / Power OFF Time / Power OFF TimeNormal Full Aspect ControlsNormal Zoom Full Is pressed During Multi PIP OperationsRGB/PC in mode Adjusting POS. /SIZEClock Phase Clock PhaseMulti PIP 1366x768@60Hz RGB, DVI, Hdmi Advanced PIPOne screen Advanced PIP Press to exit from Options menu Sub screen Main screenCinema Picture AdjustmentsStandard DynamicAdvanced Settings Mute Sound AdjustmentSelect the magnification required for the enlarged display Digital ZoomDisplay the operation guide PositionButton Forward Present Time SetupPresent Time Setup Press to set up DAY or Present Time of DAYDisplay the SET UP Timer Screen Press to select SET UP TimerPower on Time / Power OFF Time Negative / Scroll selection Mode selectionStart setting Screensaver For preventing image retentionReduces screen image retention Setup of Screensaver TimeOFF Dark MID Bright Side BAR AdjustPress to exit from Screensaver Customizing the Input labels Reduces power consumptionAddition sign Selected Input Component RGB SET UP for Input SignalsComponent / RGB in Select 3D Y/C Filter For Ntsc AV imagesPulldown / Video NR Color System / Panasonic AutoColor System FREQ. kHz / V-FREQ. Hz Setting RGB sync signalSync Refresh RateOptions Adjustments Off MENU&ENTER On Off Initial VOL Sets normal volume LevelVolume display can go up to 63 regardless of the settings Becomes the same as the Maximum VOL levelNormal Standby EnableInitial Power FunctionNormalization State regardless of the slot power setting InstallationRotate Off Does not rotate the image Weekly Command Timer Press to set each item Press to select a command numberPress to select Time / Command Time Set the time to execute a command programShipping condition Symptoms Checks TroubleshootingPlasma Display panel RGB PC input signalsCommand list of Weekly Command Timer Specifications For the U.S.A For Canada Page Customer’s Record
Top Page Image Contents