Panasonic BT-LT2600 manual System Config

Main Menu (continued)

SYSTEM CONFIG

			The underlined values are factory preset setting values.
Sub menu	Settings	Explanation
CONT./BACK.	<CONTRAST>	Used to select the function to be assigned to [CONTRAST/
	<BACKLIGHT>	BACKLIGHT] (a knob on the front panel).
		<CONTRAST>
		Used to adjust CONTRAST.
		<BACKLIGHT>
		Used to adjust BACKLIGHT.
BACKLIGHT	< 0-60 >	Used to adjust the LCD backlight level.
SUB WINDOW	<FULL>	Used to select the type of sub window.
	<PART>	<FULL>
		Used to reduce the whole input signal screen, and arrange it
		horizontally when it is displayed.
		<PART>
		Used to cut out the central section of the input signal screen, and
		arrange it horizontally when it is displayed (Displayed at the same size
		as the previous screen).
WFM POSITION	<LB>	Used to set the WFM display position.
	<RB>	<LB> Bottom left of the screen		<RB> Bottom right of the screen
	<RT>	<RT> Top right of the screen		<LT> Top left of the screen
	<LT>
MENU	<CENTER>	Used to set the on screen menu display position.
POSITION	<LB>	<CENTER> Center of the screen
	<RB>	<LB> Bottom left of the screen		<RB> Bottom right of the screen
	<RT>	<RT> Top right of the screen		<LT> Top left of the screen
	<LT>
ROTARY	<CENTER>	Used to set the picture adjusting knob status (on screen menu) display
POSITION	<LB>	position.
	<RB>	<CENTER> Center of the screen
	<RT>	<LB> Bottom left of the screen		<RB> Bottom right of the screen
	<LT>	<RT> Top right of the screen		<LT> Top left of the screen
STATUS DISPLAY	<CONTINUE>	Used to set the input signal status (on screen menu) display status.
	<3SEC OFF>	<CONTINUE> Displayed normally.
	<OFF>	<3SEC OFF> After changing status, it is displayed for approximately
			3 seconds, and then disappears.
		<OFF>	Not displayed.
SETUP LOAD	<FACTORY>	The saved factory preset setting values (FACTORY) or the user data
	<USER1> *1*2	(USER 1–USER 5) are loaded. Also after loading user data, the screen
	<USER2> *1*2	displays the signal selected before loading data.
	<USER3> *1*2
	<USER4> *1*2
	<USER5> *1*2
SETUP SAVE	<USER1>*2	Up to 5 sets of user data can be saved (J page 15).
	<USER2>*2	The menu settings and picture adjusting knob adjustment values
	<USER3>*2	(PHASE /CHROMA /BRIGHT /CONTRAST) excluding “SETUP SAVE/
	<USER4>*2	SETUP LOAD” are saved.
	<USER5>*2
FAN MOTOR	<OFF>	Used to set fan operation.
	<ON>	<OFF>	The fan is stopped. The brightness of the backlight
			automatically lowers.
		<ON>	The fan operates. The backlight brightness returns to normal.
COLOR SPACE	<EBU>*3	Used to set studio-specified colors.
	<SMPTE-C>*3

*1 When the monitor is shipped from the factory, “USER1” – “USER5” and “FACTORY” all have the same details. *2 You cannot save or load the settings for “H POSITION”, “V POSITION”, “PHASE” and “CLOCK” (J page 27). *3 Factory preset settings are The U.S.A. and Canada: SMPTE-C, Others: EBU.

21