Panasonic BT-LT2600 manual Video Config

Main Menu (continued)

VIDEO CONFIG

				The underlined values are factory preset setting values.
Sub menu	Settings	Explanation
GAMMA	<STANDARD>	Used to select the gamma curve.
SELECT*1*2	<FILM>	<STANDARD>Standard mode <FILM>FILM mode
	<STDIO/PST>	<STDIO/PST>Color emphasis mode (in the gamma characteristic in
		which shades are valued more than the contrasts, it is suitable for
		use by the studio and the post production, etc. )
		When FILM is selected,			mark is displayed in the top left of the screen.
FILM GAMMA*2	<VARICAM>	Used to select the type of FILM gamma mode.
	<OTHER>	<VARICAM>		VARICAM use
		<OTHER>		When using other types than VARICAM
COLOR TEMP.	<USER0–63>*5	Used to select the color temperature.
	<D93>	<USER0–63> Adjustable settings 0–63 (color temperature around 3000K–9300K)
	<D65>	<D93> Color temperature around 9300K
	<D56>	<D65> Color temperature around 6500K
	<VAR1>	<D56> Color temperature around 5600K
	<VAR2>	<VAR1> WB adjustment mode*4				<VAR2> WB adjustment mode*4
	<VAR3>	<VAR3> WB adjustment mode*4
SHARPNESS	<HIGH>*3	Used to select the width of the sharpness edge.
MODE*2	<LOW>	<HIGH>		Thin edge	<LOW>		Thick edge
SHARPNESS H*2	<0–30> *3	Used to set the sharpness in the horizontal direction.
		When adjusting, the item display moves to the lower part of the screen.
SHARPNESS V*2	<0–30> *3	Used to set the sharpness in the vertical direction.
		When adjusting, the item display moves to the lower part of the screen.
I-P MODE*2*6	<MODE2>	Used to select IP conversion mode. (J page 20 : About IP Mode)
	<MODE1>	<MODE2>		Field Interpolation		<MODE1> Frame Interpolation
MONO*2	<OFF>	Used to switch between color and monochrome (MONO).
	<ON>	<OFF> Color			<ON>		Monochrome
		* When this is ON, the picture adjusting knob [CHROMA] setting is fixed at 0.
ANAMO*2*7	<OFF>	If an Anamo lens has been used on the camera, and input through
	<ON>	SDI 720/60P, 59.94P, the picture is resized to Anamo size
		magnification. (a vertically compressed signal can be amplified
		vertically and corrected when it is displayed.)
SD ASPECT*2	<4:3>	Used for setting the aspect ratio settings when using SD signal input.
	<16:9>	<4:3>	4:3 display		<16:9>		16:9 display
SCAN*2	<NORMAL>	Used to set under-scan and normal display.
	<UNDER>	<NORMAL>Normal display			<UNDER>Under-scan
NOISE WIPE*2	<OFF>	<OFF> This makes a fluid and smooth contrast obtainable.
	<ON>		This is especially effective for continuously changing the contrast of
			the source signal or CG signal when the S/N is very high.
		<ON>	Noise reduction mode. Depending on the camera, this mode can
			be especially effective for dark scenes. We recommend leaving
			this setting “ON” under normal conditions.

*1 During 2 screen display, the changes are not reflected in the still image of the main window.

*2 When “RGB-COMP.” is selected in “YPBPR/RGB” in the “INPUT SELECT” menu (J page 27), this does not operate. *3 The following sharpness values can each be set,

1)VIDEO system input line (VIDEO,Y/C)(Factory settings are SHARPNESS MODE : LOW, SHARPNESS H/V : 0)

2)any other input line’s HD (Factory settings are SHARPNESS MODE : HIGH, SHARPNESS H/V : 0)

3)any other input line’s SD (Factory settings are SHARPNESS MODE : LOW, SHARPNESS H/V : 0)

and the setting values for the selected input signal from within this group is displayed. The adjustment status is displayed in the bottom right when selected.

*4 When “VAR1”, “VAR2” or “VAR3” is selected, the monitor switches to WB adjustment mode (J page 20).

*5 When selecting USER0–63

1) Push [ENTER] (USER changes to blue).	2) Select 0–63 with [ , ], and push [ENTER].
*6 When using “SUB WINDOW” function (J page 24),

1)change the setting after releasing “SUB WINDOW” function.

2)we recommand “MODE2” for the image with a fast movement. *7 During Anamo size display, “SCAN” change is not reflected.

19