Panasonic 103PF12U manual PC Input Terminals connection, Connections

Page 10

Connections

PC Input Terminals connection

COMPUTER

Conversion adapter (if necessary)

RGB

(Female)

AUDIO

PC IN

Mini D-sub 15p

PC cable

(Male)

Audio	Stereo plug
Connect a cable which matches
the audio output terminal on the computer.

Notes:

•With regard to the typical PC input signals that are described in the applicable input signals list (see page 62), adjustment values such as for the standard picture positions and sizes have already been stored in this unit. You can add up to eight PC input signal types that are not included in the list.

•Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical scanning frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.)

•The display resolution is a maximum of 1,440 × 1,080 dots when the aspect mode is set to “4:3”, and 1,920 × 1,080 dots when the aspect mode is set to “FULL”. If the display resolution exceeds these maximums, it may not be possible to show ﬁne detail with sufﬁcient clarity.

•The PC input terminals are DDC2B-compatible. If the computer being connected is not DDC2B-compatible, you will need to make setting changes to the computer at the time of connection.

•Some PC models cannot be connected to the set.

•There is no need to use an adapter for computers with DOS/V compatible Mini D-sub 15P terminal.

•The computer shown in the illustration is for example purposes only.

•Additional equipment and cables shown are not supplied with this set.

•Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the speciﬁed frequency range.

•Component Input is possible with the pin 1, 2, 3 of the Mini D-sub 15P Connector.

•Change the “COMPONENT/RGB-IN SELECT” setting in the “SET UP” menu to “COMPONENT” (when COMPONENT signal connection) or “RGB” (when RGB signal connection). (see page 50)

Signal Names for Mini D-sub 15P Connector

5 4 3 2 1

10		9	8	7	6
15	14	13	12		11

Pin Layout for PC Input Terminal

Pin No.	Signal Name	Pin No.	Signal Name	Pin No.	Signal Name
1	R (PR/CR)	6	GND (Ground)	11	NC (not connected)
2	G (Y)	7	GND (Ground)	12	SDA
3	B (PB/CB)	8	GND (Ground)	13	HD/SYNC
4	NC (not connected)	9	+5 V DC	14	VD
5	GND (Ground)	10	GND (Ground)	15	SCL

10

Image 10

Contents Model No. TH-103PF12U High Deﬁnition Plasma DisplayOperating Instructions EnglishRisk of Electric Shock Do not Open Important Safety Instructions Table of Contents Canadian Notice FCC CautionTrademark Credits Safety Precautions When using the Plasma DisplaySetup MaintenanceSafety Precautions AC Power Supply CordAccessories Supplied AccessoriesRemote Control Batteries Monitor terminal Secure any excess cables with bands as requiredSee PC Input Terminals connection Signal Names for Mini D-sub 15P ConnectorConnections Serial Terminals connection Signal names for D-sub 9P connectorCommand Communication parametersComponent / RGB connection Hdmi connectionDVD Connecting the plug to the Wall Outlet Power on / OFFConnecting the AC cord plug to the Plasma Display Right side surfacePresent Time Setup Power on / OFFWhen ﬁrst switching on the unit OSD LanguageSelecting the input signal INPUT1 INPUT2A INPUT2B INPUT3 PCBasic Controls Basic Controls On OFFAspect Controls All Aspect modePanasonic Auto During PIP Selecting the Display ModeAspect Controls During Advanced PIPTransparent Function and Insertion Function Swapping ScreensDuring Blend PIP Composite Screen Function Transparent Function Insertion FunctionSelecting the Sub Screen Position During P in P Display Selecting the Target Screen for OperationsOperations on Main screen Sub screen Select the area of the image to be enlarged Digital ZoomDisplay the operation guide Select the magniﬁcation required for the enlarged displaySelect the item Remote Control Unit Display the menu screenOn-Screen Menu Displays SetOn-Screen Menu Displays OverviewUsing Remote Control Adjusting POS. /SIZEAuto mode Adjusting POS. /SIZE 2k1k Adjusted as follows For 2k1k signalsOFF On Left On Center On Right Dynamic Picture AdjustmentsStandard CinemaAdvanced Settings Picture AdjustmentsPicture Proﬁles MEMORY1Saving proﬁles Picture ProﬁlesDeleting proﬁles Note Loading proﬁlesEditing proﬁles Renaming proﬁlesMemory Edit Locking proﬁlesMemory Save Picture Menu mode display Changing passwordsIsf Mode Setting Isf Mode Off Isf Mode OnSound Adjustment SDI Sound OutputSET UP Timer Present Time SetupPower OFF Time Screensaver For preventing image retention Mode selectionStart setting Function selectionSetup of Screensaver Time Screensaver For preventing image retentionReduces screen image retention Extended Life SettingsSide BAR Adjust Image Retention Reduction MenuReduces screen image retention Extended Life Settings when proﬁle is lockedReset Nanodrift SaverSelect the input to reset the settings AdjustSet each menu Reduces power consumption SLOT3 Customizing the Input labelsSelecting the On-Screen Menu Language Addition sign Selected InputDisplay Orientation Landscape PortraitDisplay Number locations for each arrangement Examples SET UP for Multi DisplayHow to setup Multi Display × 1 2 ×ID remote control button operation ID Remote Control FunctionSET UP for Multi Display ID CancellationPIP Advanced PIP Blend PIP Transparent Display of the Sub Screen During Blend PIPSub Screen Insertion During Blend PIP Insert LevelSET UP for Portrait How to setup PortraitLocation SET UP for PortraitViewing Area Location YUV / RGB in Select SET UP for Input SignalsComponent / RGB in Select Component RGBSET UP for Input Signals Signal menu3D Y/C Filter For Ntsc AV images Pulldown XGA ModeColor System / Panasonic Auto Color SystemNoise Reduction Press to adjustRefresh Rate Advanced NRSync Input signal displaySetting RGB sync signal SDI ThroughOptions Adjustments OptionsOptions Adjustments Button lockDelay NormalizationWeekly Command Timer Press Action ButtonShipping condition Troubleshooting Plasma Display panelList of Aspect Modes FullApplicable Input Signals Component / RGB DVI-D in ∗8MHz Active pixels Pixels Active lines Lines Applicable Input SignalsVideo input Hdmi VGA60Command list of Weekly Command Timer ∗1 These commands are unavailable on this modelSpeciﬁcations Screen sizePanasonic Professional Flat Panel Display Limited Warranty For the U.S.A and Puerto RicoLimited Warranty Statement For CanadaPage Executive Ofﬁce Customer’s RecordPanasonic Professional Display Company Panasonic Canada Inc