Panasonic 103PF12U manual Adjusting POS. /SIZE

Page 26

Adjusting POS. /SIZE

Notes:

If the dot clock frequency is 162 MHz or higher, DOT CLOCK and CLOCK PHASE cannot be made.

When digital RGB signal input, DOT CLOCK and CLOCK PHASE cannot be made.

AUTO SETUP may not work when a cropped or dark image is input. In such case, switch to a bright image with borders and other objects are clearly shown, and then try auto setup again.

Depending on the signal, out of alignment may occur after AUTO SETUP. Carry out fine tuning for the position/size as required.

If AUTO SETUP cannot set properly for vertical frequency 60Hz XGA signal (1024×768@60Hz, 1280×768@60Hz, and 1366×768@60Hz), pre-selecting the individual signal in “XGA MODE” (see page 52) may results in correct AUTO SETUP.

AUTO SETUP does not work well when a signal such as additional information is superimposed out of valid image period or intervals between synchronizing and image signals are short, or for image signal with tri-level synchronizing signal added.

If AUTO SETUP cannot adjust correctly, select “NORMALIZE” once and press ACTION () then adjust POS. /SIZE manually.

H-POS

Adjust the horizontal position.

V-POS

Adjust the vertical position.

 

 

 

 

 

 

 

H-SIZE

Adjust the horizontal size.

V-SIZE

Adjust the vertical size.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DOT

(During “COMPONENT”, “RGB” and “PC” input signal)

CLOCK

Periodic striped pattern interference (noise) may occur when a striped pattern is displayed. If this happens,

 

adjust so that any such noise is minimized.

CLOCK

(During “COMPONENT”, “RGB” and “PC” input signal)

PHASE

Eliminate the flickering and distortion.

OVER

Turn image over scan ON/OFF.

SCAN

Configurable signals are as follows:

 

525i, 525p, 625i, 625p, 750/60p, 750/50p (Component Video, RGB, DVI, SDI, HDMI)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ONOFF

Notes:

When “OFF” is set, “H-SIZE” and “V-SIZE” cannot be adjusted.

When the “Display size” is set to “On” in the Options menu, this setting will be invalid. (see page 56)

26

Image 26
Contents Model No. TH-103PF12U High Definition Plasma DisplayOperating Instructions EnglishRisk of Electric Shock Do not Open Important Safety Instructions Table of Contents Trademark Credits FCC CautionCanadian Notice Safety Precautions When using the Plasma DisplaySetup MaintenanceSafety Precautions AC Power Supply CordRemote Control Batteries AccessoriesAccessories Supplied See Secure any excess cables with bands as requiredMonitor terminal Connections Signal Names for Mini D-sub 15P ConnectorPC Input Terminals connection Serial Terminals connection Signal names for D-sub 9P connectorCommand Communication parametersDVD Hdmi connectionComponent / RGB connection Connecting the plug to the Wall Outlet Power on / OFFConnecting the AC cord plug to the Plasma Display Right side surfacePresent Time Setup Power on / OFFWhen first switching on the unit OSD LanguageSelecting the input signal INPUT1 INPUT2A INPUT2B INPUT3 PCBasic Controls Basic Controls On OFFPanasonic Auto All Aspect modeAspect Controls During PIP Selecting the Display ModeAspect Controls During Advanced PIPTransparent Function and Insertion Function Swapping ScreensDuring Blend PIP Composite Screen Function Transparent Function Insertion FunctionOperations on Main screen Sub screen Selecting the Target Screen for OperationsSelecting the Sub Screen Position During P in P Display Select the area of the image to be enlarged Digital ZoomDisplay the operation guide Select the magnification required for the enlarged displaySelect the item Remote Control Unit Display the menu screenOn-Screen Menu Displays SetOn-Screen Menu Displays OverviewAuto mode Adjusting POS. /SIZEUsing Remote Control Adjusting POS. /SIZE OFF On Left On Center On Right Adjusted as follows For 2k1k signals2k1k Dynamic Picture AdjustmentsStandard CinemaAdvanced Settings Picture AdjustmentsPicture Profiles MEMORY1Saving profiles Picture ProfilesDeleting profiles Note Loading profilesEditing profiles Renaming profilesMemory Save Locking profilesMemory Edit Picture Menu mode display Changing passwordsIsf Mode Setting Isf Mode Off Isf Mode OnSound Adjustment SDI Sound OutputPower OFF Time Present Time SetupSET UP Timer Screensaver For preventing image retention Mode selectionStart setting Function selectionSetup of Screensaver Time Screensaver For preventing image retentionReduces screen image retention Extended Life SettingsSide BAR Adjust Image Retention Reduction MenuReduces screen image retention Extended Life Settings when profile is lockedReset Nanodrift SaverSet each menu AdjustSelect the input to reset the settings Reduces power consumption SLOT3 Customizing the Input labelsSelecting the On-Screen Menu Language Addition sign Selected InputDisplay Orientation Landscape PortraitDisplay Number locations for each arrangement Examples SET UP for Multi DisplayHow to setup Multi Display × 1 2 ×ID remote control button operation ID Remote Control FunctionSET UP for Multi Display ID CancellationPIP Advanced PIP Blend PIP Transparent Display of the Sub Screen During Blend PIPSub Screen Insertion During Blend PIP Insert LevelSET UP for Portrait How to setup PortraitViewing Area Location SET UP for PortraitLocation YUV / RGB in Select SET UP for Input SignalsComponent / RGB in Select Component RGB3D Y/C Filter For Ntsc AV images Signal menuSET UP for Input Signals Pulldown XGA ModeColor System / Panasonic Auto Color SystemNoise Reduction Press to adjustRefresh Rate Advanced NRSync Input signal displaySetting RGB sync signal SDI ThroughOptions Adjustments OptionsOptions Adjustments Button lockDelay NormalizationWeekly Command Timer Press Action ButtonShipping condition Troubleshooting Plasma Display panelList of Aspect Modes FullApplicable Input Signals Component / RGB DVI-D in ∗8MHz Active pixels Pixels Active lines Lines Applicable Input SignalsVideo input Hdmi VGA60Command list of Weekly Command Timer ∗1 These commands are unavailable on this modelSpecifications Screen sizePanasonic Professional Flat Panel Display Limited Warranty For the U.S.A and Puerto RicoLimited Warranty Statement For CanadaPage Executive Office Customer’s RecordPanasonic Professional Display Company Panasonic Canada Inc