Panasonic PT-DW5000UL manual Setting projector ID number to remote control

Page 15

Setting projector ID number to remote control

Every projector has its ID number and the ID number of the controlling projector must be set to the remote control in advance so that the user can operate the remote control. The ID number of the projector is set to “ALL” on shipping, and use the ID ALL button of the remote control when using only a single projector.

Procedure of ID setting

Change the position of the operation mode selector switch to “Computer”.

Press the ID SET button, and within five seconds use the number (0 to 9) buttons to enter the 2-digit ID number set by the projector.

Change the position of the operation mode selector switch to “Projector”.

However, if the ID ALL button is pressed, the projector can be controlled regardless of the ID number of the projector (simultaneous control mode).

Attention • Do not press the ID SET button accidentally or carelessly because the ID number on the remote control can be set even when no projector is around.

If the ID SET button is pressed, the ID number goes back to the one set before pressing the ID SET button unless a numeric button is pressed within five seconds after the ID SET button is pressed.

•Your specified ID number is stored in the remote control unit unless another one is specified later. However, the stored ID will be erased if the batteries of the remote control are left exhausted. When the dry cells are replaced, set the same ID number again.

•When specifying the ID number, enter a 2-digit number even if the ID has only one digit. (Example: set “02” if the ID number is “2.”)

Using the remote control as a PC mouse

PAGE UP button

Operation mode selector switch

Left click () button

ENTER button

Right click () button

PAGE DOWN button

Operation mode selector switch

Click button

Put the knob to the Computer position.

•ENTER button

Pressing the front, rear, left and right edges of the button moves the mouse cursor up, down, left and right.

•Right click ( ) button

This button can be used as the right mouse button.

•Left click ( ) button

This button can be used as the left mouse button.

•PAGE UP button

This button can be used as the Page Up button on the PC keyboard.

•PAGE DOWN button

This button can be used as the Page Down button on the PC keyboard.

•Click button

This button can be used as the left mouse button.

Note • To use the remote control as a mouse, please purchase an optional wireless mouse receiver (model No.: ET-RMRC2).

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Commercial Use PT-DW5000ULModel number PT-D5600U/PT-D5600UL/PT-DW5000U/PT-DW5000UL Dear Panasonic CustomerPT-D5600U/PT-D5600UL/PT-DW5000U/PT-DW5000UL Contents Precautions with regard to safety Do not place liquid containers on top of the projector Do not insert any foreign objects into the projectorAlways disconnect all cables before moving the projector Do not use the old lamp unit AccessoriesUse only the Specified battery Do not look into the lens while the projector is being usedPrecautions on handling Name and function of parts Set to Computer When the operation mode selectorStatus LED lights Front and side of the projectorRear view of the main unit Controls on rear panel Side-mounted connection terminals Using the remote control unit Effective range of remote control operationLoading dry cells Setting projector ID number to remote control Using the remote control as a PC mouseOperation mode selector switch Projection schemes InstallationUsing a wired remote control Installation geometryPT-D5600U, PT-D5600UL Projection distance by projection lensInstallation 817 PT-DW5000U, PT-DW5000ULCalculation formulas for projection distance by lens types Connection Setup precautionsExample of connecting with PCs Example of connecting with AV productsPowering up the projector Making adjustment and selectionProjection Direct power off function Powering off the projectorChoose an item and adjust it using buttons How to adjust the lensHow to remove the projection lens How to adjust the lens position to the left or rightUsing the digital zoom D.ZOOM + function Automatic adjustment Auto SetupUsing the Freeze function Using the Shutter functionStructure of menu screens On-screen menusReturning to the previous Menu items settingResetting to the factory default Basic menu operationsAdjusting the picture Position Adjusting the positionTV-SYSTEM SystemClock Phase ZoomKeystone Blanking How to use Advanced MenuInput Resolution Digital Cinema RealityXGA Mode Sxga ModeRaster Position OPTION1 settings DESK/CEILING OPTION2 settingsLamp Power FRONT/REARFAN CONTROL1 PasswordFAN CONTROL2 System InformationSetting the security Connection example Setting the networkConnecting the PC System requirementsExamples of connection Using the serial terminalsPin assignments and signal names Communication conditions Factory settingPin assignments and control Control commandsCable specifications Connecting to a PC Computer Projector DTE specificationsIndication of lamp monitor Dismantle the air filter Cleaning and replacement of air filterProcedure of cleaning Clean the air filterReplacing the lamp unit Timing of lamp unit replacementHave a Phillips screwdriver ready ahead of time Lamp unit replacement stepsRemove the two screws securing the fan unit Lamp unit will be hot after it has been usedSelect the lamp which has been replaced with the and buttons Click OK Using Web Browser ControlAccessing from the Web browser Password changeBasic control Mail set up buttonPower On/Off control Shutter control Change password buttonError information Monitor informationOK Normal operation Failed Occurrence of trouble When Failed has appeared for an item Parameter Description Mail setupError Mail setup page ContinuingPing test DNS server set upPOP server setup Button to update settingsAdjust clock Contents of mail sentNetwork status Network configCommand Control Description Remarks Using the PJLink protocolSupported commands PJLink security authenticationNot turn on Symptoms ChecksPower does Remote controlPT-D5600U PT-D5600UL PT-DW5000U SpecificationsWireless mouse receiver Length of power supply cord CabinetOutside dimensions Remote control Power sourcePAL-M/PAL60 PAL/PAL-N/SECAM Compatible Signal ListDimensions Installation dimensions diagramTrademark Acknowledgement Concernant LA Sécurité Ne pas retirer le couvercle ou le modifier Précautions concernant la sécuritéNe pas couvrir le filtre et la sortie d’air Ne pas surcharger la prise de courantNe pas placer le projecteur sur des surfaces instables Ne pas placer des récipients de liquide sur le projecteurNe pas mettre d’objets étrangers dans le projecteur Ne pas placer d’objets lourds sur le projecteur ’utiliser que la pile indiquée’utilisez pas un bloc lampe usagé Mise au rebut Nettoyage et maintenancePrécautions pour la manipulation Précautions pour le transportPériode de remplacement de la lampe Remplacement de la lampeProcédure de remplacement de la lampe La lampe est chaude si elle vient d’être utiliséePréparez un tournevis Phillips à l’avance INIT. Compt Panasonic Projector Systems Company Technical SupportPanasonic Canada Inc

PT-DW5000UL specifications

The Panasonic PT-DW5000UL is a cutting-edge projection solution designed for professional use in various environments, including conferences, events, and large venues. Boasting a compact and lightweight design, this projector offers an impressive balance of high performance and portability, making it an excellent choice for users who require mobility without compromising on image quality.

At the heart of the PT-DW5000UL is its powerful DLP technology, which delivers stunning 5000 lumens brightness and a native resolution of 1920 x 1200 pixels. This outstanding resolution ensures that images are sharp, detailed, and vibrant, making it well-suited for displaying high-definition content, intricate graphics, and dynamic presentations. The projector’s high brightness level is particularly advantageous in well-lit environments, allowing for clear visibility even in challenging lighting conditions.

One of the standout features of the PT-DW5000UL is its advanced Solid Shine laser technology. This innovation eliminates the need for traditional lamps, resulting in a longer lifespan of up to 20,000 hours. This increase in operational longevity not only reduces maintenance costs but also ensures consistent performance over time. Moreover, the laser light source provides stable brightness and vivid colors throughout its lifespan, ensuring that every presentation looks its best.

The projector also incorporates a highly effective Dynamic Contrast feature, which enhances the depth of the images by adjusting light output automatically based on the content being displayed. This capability results in deeper blacks and brighter highlights, creating a more immersive viewing experience.

Connectivity is another significant characteristic of the PT-DW5000UL. It supports a wide range of inputs, including HDMI, DVI-D, and 5BNC, allowing seamless integration with various devices. Furthermore, the projector supports multi-screen and edge blending capabilities, making it suitable for large-scale presentations and installations that require multiple projectors to work in harmony.

For ease of installation, the PT-DW5000UL features a variety of lens options and a flexible lens shift range, enabling users to adjust the image position without distortion. This adaptability makes it suitable for different venue configurations, whether in an auditorium or an outdoor setting.

In conclusion, the Panasonic PT-DW5000UL stands out as a robust and reliable projector that combines advanced technology with user-friendly features. Its powerful brightness, exceptional image quality, and long-lasting performance make it an ideal choice for professionals seeking a versatile solution for their projection needs.
Top Page Image Contents