Panasonic PT-DW5000UL manual Adjusting the position, Tv-System, Position, Aspect

Page 30

Adjusting the picture

AI

Gray scale control is exercised to suit the images, and optimal images with a clear contrast are projected.

ON : AI compensation is enabled.

OFF : AI compensation is disabled.

TV-SYSTEM

(For S-Video/Video signals)

The setting that corresponds to the TV system is selected here.

AUTO1 : Standard setting

Automatically selects the TV standard that matches the input video signal, out of NTSC, PAL, NTSC4.43, SECAM and PAL60.

AUTO2 : Automatically selects the TV standard that matches the input video signal, out of NTSC, PAL-M, and PAL-N.

•Normally “AUTO1” or “AUTO2” should be chosen for this option.

•If the video signals are not displayed properly due to signal deterioration, choose the TV system that matches the input video signals.

Automatically selected by detecting the horizontal/vertical scan frequencies and color sub- carrier listed in the table below:

Signal

H. Scan

V. Scan

Color

Frequency

Frequency

Subcarrier

System

(kHz)

(Hz)

(MHz)

 

 

 

 

 

NTSC

15.75

60.00

3.58

 

 

 

 

NTSC4.43

15.75

60.00

4.43

 

 

 

PAL

15.63

50.00

 

 

 

 

 

PAL-M

15.75

60.00

3.58

 

 

 

PAL-N

15.63

50.00

 

 

 

 

 

SECAM

15.63

50.00

4.25 or 4.41

PLA60

15.75

60.00

4.43

 

 

 

 

SYSTEM

(For RGB/YPBPR signals)

This enables the RGB system or YPBPR system to be selected.

For the signals which are supported, refer to page 58.

Adjusting the position

 

 

 

 

 

 

 

POSITION

 

 

 

 

 

 

 

POSITION

 

 

 

 

 

 

 

 

 

 

 

 

 

ASPECT

 

 

 

 

 

 

4 : 3

 

 

 

 

ZOOM

 

 

 

 

 

 

 

 

 

 

 

 

 

CLOCK PHASE

 

 

 

 

 

 

16

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

KEYSTONE

 

 

 

 

 

 

 

 

 

 

 

 

 

SELECT

 

 

 

 

 

ENTER

 

 

RETRN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

POSITION

The position where the images are displayed can be moved here.

: The position is moved horizontally. : The position is moved vertically.

ASPECT

AUTO : (For S-Video/Video signals only)

At this setting, when S1 video signals 1 are identified as being input to the S- Video connector or video ID signals are identified as being input to the video connector, the images are displayed after automatically being converted to the 16:9 aspect ratio.

16:9 : At this setting, when standard signals 2 are input, the images are converted to the 16:9 aspect ratio and displayed. When wide-screen signals 3 are input, the images are displayed with their inherent aspect ratio intact.

4:3 : At this setting, when standard signals 2 are input, the images are displayed with their inherent aspect ratio intact. When wide-screen signals 3 are input, they are converted by the PT-D5600U to the 4:3 aspect ratio and displayed. With the PT- DW5000U, the images are reduced in size and displayed without converting their aspect ratio so that they will fit onto a screen with a 4:3 aspect ratio.

S4:3 : Select this setting when using a 16:9 screen.

HV FIT : At this setting, the images are displayed to fill the entire screen.

If the aspect ratios of the input signals and screen differ, the images are converted into the screen’s aspect ratio (4:3 for the PT-D5600U or 15:9 for the PT-DW5000U) and displayed.

1 S1 video signals are 16:9 video signals to which is added the detection signal output from the video deck or other unit which supports the wide-screen format.

2 Here, the standard signal means 4:3 or 5:4 input signals.

3 Here, the wide-screen signals means 16:9, 15:9 or 15:10 input signals.

30

Page 29 Page 31
Image 30
Page 29 Page 31
Contents PT-DW5000UL Commercial UseDear Panasonic Customer Model number PT-D5600U/PT-D5600UL/PT-DW5000U/PT-DW5000ULPT-D5600U/PT-D5600UL/PT-DW5000U/PT-DW5000UL Contents Precautions with regard to safety Do not place liquid containers on top of the projector Do not insert any foreign objects into the projectorAlways disconnect all cables before moving the projector Do not look into the lens while the projector is being used AccessoriesUse only the Specified battery Do not use the old lamp unitPrecautions on handling Name and function of parts When the operation mode selector Set to ComputerFront and side of the projector Status LED lightsRear view of the main unit Controls on rear panel Side-mounted connection terminals Using the remote control unit Effective range of remote control operationLoading dry cells Setting projector ID number to remote control Using the remote control as a PC mouseOperation mode selector switch Installation geometry InstallationUsing a wired remote control Projection schemesProjection distance by projection lens PT-D5600U, PT-D5600ULInstallation PT-DW5000U, PT-DW5000UL 817Calculation formulas for projection distance by lens types Setup precautions ConnectionExample of connecting with AV products Example of connecting with PCsPowering up the projector Making adjustment and selectionProjection Powering off the projector Direct power off functionHow to adjust the lens position to the left or right How to adjust the lensHow to remove the projection lens Choose an item and adjust it using buttonsUsing the Shutter function Automatic adjustment Auto SetupUsing the Freeze function Using the digital zoom D.ZOOM + functionOn-screen menus Structure of menu screensBasic menu operations Menu items settingResetting to the factory default Returning to the previousAdjusting the picture System Adjusting the positionTV-SYSTEM PositionClock Phase ZoomKeystone Digital Cinema Reality How to use Advanced MenuInput Resolution BlankingXGA Mode Sxga ModeRaster Position OPTION1 settings FRONT/REAR OPTION2 settingsLamp Power DESK/CEILINGSystem Information PasswordFAN CONTROL2 FAN CONTROL1Setting the security System requirements Setting the networkConnecting the PC Connection exampleCommunication conditions Factory setting Using the serial terminalsPin assignments and signal names Examples of connectionConnecting to a PC Computer Projector DTE specifications Control commandsCable specifications Pin assignments and controlIndication of lamp monitor Clean the air filter Cleaning and replacement of air filterProcedure of cleaning Dismantle the air filterTiming of lamp unit replacement Replacing the lamp unitLamp unit will be hot after it has been used Lamp unit replacement stepsRemove the two screws securing the fan unit Have a Phillips screwdriver ready ahead of timeSelect the lamp which has been replaced with the and buttons Password change Using Web Browser ControlAccessing from the Web browser Click OKChange password button Mail set up buttonPower On/Off control Shutter control Basic controlError information Monitor informationOK Normal operation Failed Occurrence of trouble Mail setup When Failed has appeared for an item Parameter DescriptionMail setup page Continuing ErrorButton to update settings DNS server set upPOP server setup Ping testContents of mail sent Adjust clockNetwork config Network statusPJLink security authentication Using the PJLink protocolSupported commands Command Control Description RemarksRemote control Symptoms ChecksPower does Not turn onSpecifications PT-D5600U PT-D5600UL PT-DW5000URemote control Power source Length of power supply cord CabinetOutside dimensions Wireless mouse receiverCompatible Signal List PAL-M/PAL60 PAL/PAL-N/SECAMDimensions Installation dimensions diagramTrademark Acknowledgement Concernant LA Sécurité Ne pas surcharger la prise de courant Précautions concernant la sécuritéNe pas couvrir le filtre et la sortie d’air Ne pas retirer le couvercle ou le modifierNe pas placer le projecteur sur des surfaces instables Ne pas placer des récipients de liquide sur le projecteurNe pas mettre d’objets étrangers dans le projecteur Ne pas placer d’objets lourds sur le projecteur ’utiliser que la pile indiquée’utilisez pas un bloc lampe usagé Précautions pour le transport Nettoyage et maintenancePrécautions pour la manipulation Mise au rebutRemplacement de la lampe Période de remplacement de la lampeProcédure de remplacement de la lampe La lampe est chaude si elle vient d’être utiliséePréparez un tournevis Phillips à l’avance INIT. Compt Panasonic Projector Systems Company Technical SupportPanasonic Canada Inc

PT-DW5000UL specifications

The Panasonic PT-DW5000UL is a cutting-edge projection solution designed for professional use in various environments, including conferences, events, and large venues. Boasting a compact and lightweight design, this projector offers an impressive balance of high performance and portability, making it an excellent choice for users who require mobility without compromising on image quality.

At the heart of the PT-DW5000UL is its powerful DLP technology, which delivers stunning 5000 lumens brightness and a native resolution of 1920 x 1200 pixels. This outstanding resolution ensures that images are sharp, detailed, and vibrant, making it well-suited for displaying high-definition content, intricate graphics, and dynamic presentations. The projector’s high brightness level is particularly advantageous in well-lit environments, allowing for clear visibility even in challenging lighting conditions.

One of the standout features of the PT-DW5000UL is its advanced Solid Shine laser technology. This innovation eliminates the need for traditional lamps, resulting in a longer lifespan of up to 20,000 hours. This increase in operational longevity not only reduces maintenance costs but also ensures consistent performance over time. Moreover, the laser light source provides stable brightness and vivid colors throughout its lifespan, ensuring that every presentation looks its best.

The projector also incorporates a highly effective Dynamic Contrast feature, which enhances the depth of the images by adjusting light output automatically based on the content being displayed. This capability results in deeper blacks and brighter highlights, creating a more immersive viewing experience.

Connectivity is another significant characteristic of the PT-DW5000UL. It supports a wide range of inputs, including HDMI, DVI-D, and 5BNC, allowing seamless integration with various devices. Furthermore, the projector supports multi-screen and edge blending capabilities, making it suitable for large-scale presentations and installations that require multiple projectors to work in harmony.

For ease of installation, the PT-DW5000UL features a variety of lens options and a flexible lens shift range, enabling users to adjust the image position without distortion. This adaptability makes it suitable for different venue configurations, whether in an auditorium or an outdoor setting.

In conclusion, the Panasonic PT-DW5000UL stands out as a robust and reliable projector that combines advanced technology with user-friendly features. Its powerful brightness, exceptional image quality, and long-lasting performance make it an ideal choice for professionals seeking a versatile solution for their projection needs.
Top Page Image Contents