Panasonic PT-DW5000UL Projection, Powering up the projector, Making adjustment and selection

Page 23

Projection

 

 

 

R/PR G/Y B/PB

SYNC/HD VD

 

VIDEO IN S-VIDEO IN

RGB 1 IN

 

 

REMOTE 1

REMOTE 2

IN

SE

IN OUT

 

 

 

Powering up the projector

When using an optional lens, install a projection lens before powering up the projector. (Refer to page 25.)

Remove the lens cover beforehand.

Connect the supplied power cable. (120 V AC, 50 Hz/60 Hz)

Press the “ I ” marked side of the MAIN POWER switch to turn on the power.

The power indicator lights up red, and the projector is placed in the standby mode.

Press the “ I ” button. [on the main unit or the remote control]

The power indicator illuminates in green and soon the image is projected on the screen.

Making adjustment and selection

Press the LENS button three times to adjust the lens shift. (Refer to page 25.)

Press the AUTO SETUP button if the input signal is RGB/DVI signal. (Refer to page 26.) [on the main unit or the remote control]

Fit the image size to the screen size.

Press the LENS button twice and adjust the zoom of the lens on the lens zoom adjustment menu.

Press the LENS button and adjust the focus of the lens on the lens focus adjustment menu.

Display the zoom adjustment menu again and adjust the zoom of the lens to fit the image size to the screen size. (Refer to page 25.)

Roughly adjust the focus of the lens.

Note • If the projector is powered up at about 0 ˚C,

(Refer to page 25.)

 

a warm-up period of approximately five

Press the LENS button on the main unit or the

minutes may be necessary to start

projection.

remote control unit to display a focus adjustment

The temperature monitor (TEMP) lights

screen. Pressing

buttons to adjust the

during the warm-up period.

image into focus.

 

 

When the warm-up is completed, the

Select and set the projection scheme.

temperature monitor (TEMP) turns off and

(Refer to page 35.)

 

the image is projected on the screen.

Select the input signal by pressing the

• If the surrounding temperature is very low

and the warm-up period exceeds five

input selector button to toggle through

minutes, the control determines it as an

RGB1, RGB2, VIDEO, S-VIDEO and DVI.

abnormal condition and turns off the

[on the main unit or the remote control]

power automatically. If this happens, raise

Turn the feet, and adjust the tilt of the

the surrounding temperature to 0 °C or

higher and then turn the main power “on”

main unit in the front and rear or left

and turn the power “on” ( ).

and right.

 

• It is recommended that the projector be

Use the lens left/right adjustment dial to

allowed to warm up for at least 30 minutes

before any adjustments are made to the

adjust the direction of the lens. (page 25)

focus.

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Commercial Use PT-DW5000ULModel number PT-D5600U/PT-D5600UL/PT-DW5000U/PT-DW5000UL Dear Panasonic CustomerPT-D5600U/PT-D5600UL/PT-DW5000U/PT-DW5000UL Contents Precautions with regard to safety Always disconnect all cables before moving the projector Do not place liquid containers on top of the projectorDo not insert any foreign objects into the projector Do not use the old lamp unit AccessoriesUse only the Specified battery Do not look into the lens while the projector is being usedPrecautions on handling Name and function of parts Set to Computer When the operation mode selectorStatus LED lights Front and side of the projectorRear view of the main unit Controls on rear panel Side-mounted connection terminals Loading dry cells Using the remote control unitEffective range of remote control operation Operation mode selector switch Setting projector ID number to remote controlUsing the remote control as a PC mouse Projection schemes InstallationUsing a wired remote control Installation geometryPT-D5600U, PT-D5600UL Projection distance by projection lensInstallation 817 PT-DW5000U, PT-DW5000ULCalculation formulas for projection distance by lens types Connection Setup precautionsExample of connecting with PCs Example of connecting with AV productsProjection Powering up the projectorMaking adjustment and selection Direct power off function Powering off the projectorChoose an item and adjust it using buttons How to adjust the lensHow to remove the projection lens How to adjust the lens position to the left or rightUsing the digital zoom D.ZOOM + function Automatic adjustment Auto SetupUsing the Freeze function Using the Shutter functionStructure of menu screens On-screen menusReturning to the previous Menu items settingResetting to the factory default Basic menu operationsAdjusting the picture Position Adjusting the positionTV-SYSTEM SystemKeystone Clock PhaseZoom Blanking How to use Advanced MenuInput Resolution Digital Cinema RealityRaster Position XGA ModeSxga Mode OPTION1 settings DESK/CEILING OPTION2 settingsLamp Power FRONT/REARFAN CONTROL1 PasswordFAN CONTROL2 System InformationSetting the security Connection example Setting the networkConnecting the PC System requirementsExamples of connection Using the serial terminalsPin assignments and signal names Communication conditions Factory settingPin assignments and control Control commandsCable specifications Connecting to a PC Computer Projector DTE specificationsIndication of lamp monitor Dismantle the air filter Cleaning and replacement of air filterProcedure of cleaning Clean the air filterReplacing the lamp unit Timing of lamp unit replacementHave a Phillips screwdriver ready ahead of time Lamp unit replacement stepsRemove the two screws securing the fan unit Lamp unit will be hot after it has been usedSelect the lamp which has been replaced with the and buttons Click OK Using Web Browser ControlAccessing from the Web browser Password changeBasic control Mail set up buttonPower On/Off control Shutter control Change password buttonOK Normal operation Failed Occurrence of trouble Error informationMonitor information When Failed has appeared for an item Parameter Description Mail setupError Mail setup page ContinuingPing test DNS server set upPOP server setup Button to update settingsAdjust clock Contents of mail sentNetwork status Network configCommand Control Description Remarks Using the PJLink protocolSupported commands PJLink security authenticationNot turn on Symptoms ChecksPower does Remote controlPT-D5600U PT-D5600UL PT-DW5000U SpecificationsWireless mouse receiver Length of power supply cord CabinetOutside dimensions Remote control Power sourcePAL-M/PAL60 PAL/PAL-N/SECAM Compatible Signal ListTrademark Acknowledgement DimensionsInstallation dimensions diagram Concernant LA Sécurité Ne pas retirer le couvercle ou le modifier Précautions concernant la sécuritéNe pas couvrir le filtre et la sortie d’air Ne pas surcharger la prise de courantNe pas mettre d’objets étrangers dans le projecteur Ne pas placer le projecteur sur des surfaces instablesNe pas placer des récipients de liquide sur le projecteur ’utilisez pas un bloc lampe usagé Ne pas placer d’objets lourds sur le projecteur’utiliser que la pile indiquée Mise au rebut Nettoyage et maintenancePrécautions pour la manipulation Précautions pour le transportPériode de remplacement de la lampe Remplacement de la lampePréparez un tournevis Phillips à l’avance Procédure de remplacement de la lampeLa lampe est chaude si elle vient d’être utilisée INIT. Compt Panasonic Canada Inc Panasonic Projector Systems CompanyTechnical Support

PT-DW5000UL specifications

The Panasonic PT-DW5000UL is a cutting-edge projection solution designed for professional use in various environments, including conferences, events, and large venues. Boasting a compact and lightweight design, this projector offers an impressive balance of high performance and portability, making it an excellent choice for users who require mobility without compromising on image quality.

At the heart of the PT-DW5000UL is its powerful DLP technology, which delivers stunning 5000 lumens brightness and a native resolution of 1920 x 1200 pixels. This outstanding resolution ensures that images are sharp, detailed, and vibrant, making it well-suited for displaying high-definition content, intricate graphics, and dynamic presentations. The projector’s high brightness level is particularly advantageous in well-lit environments, allowing for clear visibility even in challenging lighting conditions.

One of the standout features of the PT-DW5000UL is its advanced Solid Shine laser technology. This innovation eliminates the need for traditional lamps, resulting in a longer lifespan of up to 20,000 hours. This increase in operational longevity not only reduces maintenance costs but also ensures consistent performance over time. Moreover, the laser light source provides stable brightness and vivid colors throughout its lifespan, ensuring that every presentation looks its best.

The projector also incorporates a highly effective Dynamic Contrast feature, which enhances the depth of the images by adjusting light output automatically based on the content being displayed. This capability results in deeper blacks and brighter highlights, creating a more immersive viewing experience.

Connectivity is another significant characteristic of the PT-DW5000UL. It supports a wide range of inputs, including HDMI, DVI-D, and 5BNC, allowing seamless integration with various devices. Furthermore, the projector supports multi-screen and edge blending capabilities, making it suitable for large-scale presentations and installations that require multiple projectors to work in harmony.

For ease of installation, the PT-DW5000UL features a variety of lens options and a flexible lens shift range, enabling users to adjust the image position without distortion. This adaptability makes it suitable for different venue configurations, whether in an auditorium or an outdoor setting.

In conclusion, the Panasonic PT-DW5000UL stands out as a robust and reliable projector that combines advanced technology with user-friendly features. Its powerful brightness, exceptional image quality, and long-lasting performance make it an ideal choice for professionals seeking a versatile solution for their projection needs.
Top Page Image Contents