REMOTE CONTROL OPERATION (FOR MODELS
Programming The Remote Control
The Universal Remote Control can be programmed to operate many manufacturers’ components, using the component function buttons for VCR, DVD, AUX, RCVR, TV, DTV CABLE or DBS. Follow the procedures for programming your Remote Control with or without a code for the component.
Default Modes for Remote Control
Device |
| Operates |
| Default |
TV |
| TV (Panasonic Only) |
| Panasonic TV Code |
| DTV (Panasonic Only) |
| Panasonic DTV Code | |
CABLE |
| CABLE (Preset) |
| Panasonic CABLE |
|
| Code | ||
|
|
|
| |
DBS |
| DBS (Preset) |
| Panasonic DBS Code |
VCR |
| VCR (Preset0 |
| Panasonic VCR Codes |
DVD/CD |
| DVD and CD (Preset) |
| Panasonic DVD Codes |
AUX |
| Personal Video Recorders, |
| Panasonic Personal |
| Tape and VCR2 |
| Video Recorder Code | |
|
|
| ||
RCVR |
| Audio receiver (Preset) |
| Panasonic RCVR code |
Note: Determine the manufacturer of the component and look in the table for the code.
Programming with a Code
Procedure
1.Confirm that the external component is plugged in and operating.
2.Turn the component off.
ACTION
3. Press | and POWER together, for at least 5 |
seconds. After 5 seconds, the illuminated mode (component) buttons will begin to flash. Release the ACTION and POWER buttons.
4.Press appropriate component button on the Remote Control VCR, DVD (CD), AUX (VCR2 or TAPE), RCVR, DTV, CABLE or DBS. The component button will illuminate steadily and all others will go out.
5.Enter the
6.Press the Remote Control POWER to test the
component. If the procedure was successful, the component will turn on and the component key will blink twice and then go out.
Note: If the component does not operate with the Remote Control, repeat steps 3 through 6 using another code (some brands have multiple codes). If an incorrect code is entered, or if the procedure takes longer than 30 seconds, the programming will fail.
Programming without a Code
This procedure searches all codes and is called the “sequence method.”
1.Confirm that the external component is plugged in and on.
2.Turn the component off.
ACTION
3. Press | and POWER together, for at least 5 |
seconds. After 5 seconds, the illuminated mode (component) buttons will begin to flash. Release the ACTION and POWER buttons.
4.Press appropriate component button on the Remote Control. The component button will illuminate steadily and all others will go out.
5. Press the POWER button to set the remote control into the step and set mode.
6.Point the remote control towards the component.
7.Press VOL (the mode key will blink three times), then press the Remote Control POWER button to test the
component. Continue this process until the proper code is found. If the procedure was successful, the component will turn on.
Note: | Each time you press the VOL button, make sure that the | |
| component key blinks twice before pressing the POWER | |
| button. |
|
8. | Once the device responds, press | ACTION |
to store the | ||
code. The mode (component) button will blink twice.
Note: It may take | many attempts before | the correct code |
is found. If you miss a code, press | VOL, then press | |
the POWER | button to test the component. | |
Component Codes
The Universal Remote Control is capable of operating many component brands after entering a code. Some components may not operate because the codes are not available due to limited memory. The Universal Remote Control does not control all features found in each model.
Write the code numbers from tables in this space. This will serve as a reference if you need to program your Remote Control.
| VCR |
| DVD |
| DVD (CD) | |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
AUX (VCR2) | AUX (TAPE) | RECEIVER | ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ENGLISH |
DTV |
| CABLE |
| DBS | ||||||
|
|
|
|
|
|
|
|
|
|
|
19z