Sanyo CD-RW880 Recording, Load a recordable CD-R or CD-RW disc into the unit, Digital Optical

Page 16

Recording

1 6 4

3 2 5

1Load a recordable CD-R or CD-RW disc into the unit.

Press the OPEN/CLOSE button (L), place a disc on the disc tray with the printed label side up, and then press the OPEN/CLOSE button (L) to close the disc tray.

Make sure NO TOC and “CD-R” (or “CD-RW”) indicators lights on the display.

2Select the source to be recorded using the INPUT SELECT button.

DIGITAL (OPTICAL IN)

Select this to record a source connected to the DIGITAL IN terminal.

ANALOG (ANALOG IN)

Select this to record a source connected to the ANALOG IN terminal.

3If necessary, select the mode of track number assignment using the AUTO/MANUAL button.

When the POWER button or the STANDBY/ON button is pressed, this setting is reset to –60 dB.

See page 18 for details.

4Press the RECORD button.

and J indicators on the display will light, and the unit enters record pause mode.

<No button will work while “WAITING” is displayed. Wait a few seconds until “WAITING” disappears from the display. When DIGITAL is selected in step 2 , the sampling frequency of the digital source (“FS 44_1K”, “FS 48K” or “ FS 32K”) briefly appears after “WAITING”.

<“DIN UNLOCK” appears when the unit cannot perceive the digital signal. In that case, connect a digital device to the DIGITAL IN terminal, switch it on, and wait a few seconds until the unit enters record pause mode.

<You cannot record if “MONITOR” appears on the display. In that case, reload a recordable disc, wait a few seconds until NO TOC and “CD-R” (or “CD-RW”) indicators light on the display, and press the RECORD button again.

5If necessary, adjust the recording level using the REC LEVEL buttons.

Play the source to be recorded and adjust the recording level so that the loudest sound does not exceed the “OVER” indicator on the peak level meter.

The level can be adjusted from –∞, –60 dB to +18 dB.

<Unlike analog equipment, digital audio units produce extremely unpleasant sounds when distorted, and there is no “headroom” after the 0 mark. When you record digitally from a commercially-produced CD, set the digital volume to 0 dB. This will maintain all the dynamic range of the source CD without clipping. Only boost the signal if the source is exceptionally quiet.

When the POWER button or the OPEN/CLOSE button is pressed, the recording level is reset to 0 dB.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents CD-RW880 Important Safety Instructions For U.S.A Type SF-W36FR Manufacturer Laser outputContents Before using the unitAC Power Cord ConnectionsAnalog IN/OUT jacks Digital in terminalDiscs CD-RCD-RWRemote Control Unit Battery InstallationAbout CD-R and CD-RW discs FinalizingUnit Functions and Remote Control O N M L K JPower OPEN/CLOSEMusic Skip Pause JListening to a CD CD-RCD-RW CD-R no TOCStandby mode To suspend playback temporarily pause modeTo stop playbacks To skip to the next or a previous trackShuffle Playback Direct PlaybackTime Display Repeat Playback RepeatTo repeat a designated section Repeat ALL Repeat All the TracksProgrammed Playback Press the Program button in the stop modePress the numeric button to select a track Before Recording Recording Load a recordable CD-R or CD-RW disc into the unitDigital Optical Analog AnalogManual track division Input MonitoringAutomatic Track Division Track -60, -50, -40 or -30 dBSynchronous Recording To start synchronous recordingSync ALL SyncFinalize Press the Play y button to start finalizingErase or Unfinalize a CD-RW Erase and the number of the last track recorded on the discErase Disc RefreshTroubleshooting MaintenanceCD Recorder Beware of condensationSpecifications Error MessagesMessages MessagesSommaire Avant l’utilisationAvertissement Quand Vous Déplacez CET L’APPAREILRaccordement Prises d’entrée et sorties Analog IN/OUTSortie Digital OUT Cordon d’alimentation ACDisques Boîtier de télécommande Remarques concernant les disques compacts CD-R et CD-RWFinalisation Mise en place des pilesNomenclatures des controles Capteur de télécommande Affichage Plateau porte-disqueTouches numériques RemarqueAppuyez sur l’interrupteur Power Écoute de CDAppuyez sur la touche OPEN/CLOSE L pour fermer le tiroir Appuyez sur la touche Play y pour engendrer la lectureMode veille Pour suspendre la lecture momentanément mode pausePour arrêter la lecture Pour sauter au morceau suivant ou précédantLecture aléatoire Lecture DirecteAffichage du temps Lecture répétée Répétition A-BRépétition d’une section désignée Repeat ALL Répétition de tout le disqueEn mode arrêt, appuyez sur la touche Program Lecture ProgramméePour contrôler l’ordre programmé Pour ajouter un morceau à la fin du programmeAvant d’enregistrer Pour enlever un morceau de la liste programméePour effacer la liste programmée Système de gestion de copie en sérieEnregistrement Appuyer sur la touche RecordDivision manuelle de morceau Contrôle d’entréeDivision automatique de morceau Track -60, -50, -40 ou -30 dBEnregistrement synchronisé Pour démarrer l’enregistrement synchroniséFinalisation Appuyez sur la touche Play y pour commencer la finalisationEffacement ou dé-finalisation d’un CD-RW Dépannage Lecteur CDMise en garde sur la condensation EntretienAccessoires standard SpécificationsAffichage des erreurs FS 441K, FS 32K ou FS 48KTeac Corporation

CD-RW880 specifications

The Sanyo CD-RW880 is a well-regarded audio device that embodies the transition from analog to digital media. As a versatile CD recorder, it captures both the nostalgia of traditional CD playback and the conveniences of modern digital recording technology. Designed for music enthusiasts and professionals alike, the CD-RW880 features a range of specifications that enhance its performance and usability.

One of the standout features of the Sanyo CD-RW880 is its ability to record onto CD-R and CD-RW discs. This flexibility allows users to create custom compilations and backup their favorite tracks with ease. The device supports a range of recording speeds, which includes options for both high-speed recording and standard speeds that ensure optimal quality. The capability to erase and re-record on CD-RW media further distinguishes it from standard CD players, providing a convenient and practical solution for digital music management.

The CD-RW880 employs advanced digital signal processing (DSP) technology, which plays a crucial role in maintaining audio fidelity during both playback and recording. It features a built-in A/D converter that ensures high-quality sound reproduction while minimizing noise and distortion. With a signal-to-noise ratio that meets professional standards, users can expect clear and accurate audio playback, whether they are recording live performances or transferring existing CDs.

Additionally, the Sanyo CD-RW880 is equipped with a user-friendly interface that makes navigation intuitive. The front panel includes dedicated buttons for recording, play, pause, and track selection, providing a seamless experience for users of all skill levels. The inclusion of a LCD display gives users quick access to important information such as track number, recording time, and remaining space on the disc.

Another noteworthy characteristic is the device's compatibility with both audio and data CDs, allowing it to function not just as an audio recorder but also as a versatile media player. This feature opens up possibilities for creating data backups and archiving important files onto CD format, which can be a useful addition for both personal and professional uses.

In summary, the Sanyo CD-RW880 is a multifunctional CD recorder that appeals to a broad audience from casual music lovers to professionals in the industry. With its solid recording capabilities, superior audio quality, and user-centric design, this device stands as a reliable choice for anyone looking to bridge the gap between analog sound and digital convenience. Whether for creating custom playlists, transferring music, or archiving precious audio content, the CD-RW880 continues to be a valuable tool in an increasingly digital world.
Top Page Image Contents