Panasonic DMR-E100H warranty Manually programming timer recordings

Manually programming timer recordings

You can enter up to 32 programs up to a month in advance. Each daily or weekly program is counted as one program.

1 Press [PROG/CHECK].

TIMER		Remain HDD 17:36 SP				DVD 1:42 SP
RECORDING
					3/26 TUE 12:55 PM
No	CHANNEL	DATE	ON	OFF	MODE	DRIVE CHECK
01	64 ABC	3/ 26 TUE	1:00 PM	2:00 PM	SP	Enable
		New Timer Program

SELECT

CANCEL Press ENTER or VCR Plus+ to

ENTER RETURN store new program.

2 Press [3, 4] to select “New Timer

Program” and press [ENTER].

TIMER		Remain HDD 17:36 SP DVD				1:42 SP
RECORDING
					3/26 TUE 12:55 PM
	CHANNEL	DATE	ON	OFF	MODE	DRIVE
	3	----------	--:-- --	--:-- --	--	---
	----4
					Enter Title
		Please set Channel.
SELECT				No.
			0	-- 9
ENTER	RETURN

3 Press [1] to move through the items

and change the items with [3, 4].

≥The current settings are shown each time you press [1].

≥You may use the numbered buttons to enter the CHANNEL, DATE, ON (start Time), and OFF (Finish Time).

TIMER
RECORDING	Remain HDD	17:36 SP	DVD	1:42 SP
		3/26 TUE 12:55 PM
CHANNEL DATE	ON	OFF MODE		DRIVE

64 ABC 3/ 26 TUE 2:30 PM 3:00 PM SP HDD

Enter Title

≥CHANNEL (Channel number and caption)

≥DATE

[.Current date

l;:

lNext day up to one month later minus one day

l;:

lWeekly timer: SUN-SAT>MON-SAT>MON-FRI

l;:

{.Daily timer: WEEKLY SUN>--->WEEKLY SAT

≥ON (Start time)/OFF (Finish time)

The time increases or decreases in 30-minute increments if you hold the button.

≥MODE (Recording mode ➜ page 15)

SP>XP>FR>EP>LP (>Return to SP)

≥DRIVE HDD()DVD

≥RENEW (➜ page 28, Auto Renewal Recording)

Only when you set daily or weekly recording onto HDD –You cannot set if “MPEG4 Rec mode”➜( page 52) is set to

either “SF”, “F”, “N”, or “E”. ON()OFF

≥Enter Title

Select “Enter Title” using 2[ , 1] and press [ENTER] (➜ page 46).

4 Press [ENTER] when you have finished programming the timer.

TIMER		Remain HDD 17:36 SP				DVD 1:42 SP
RECORDING
					3/26 TUE 12:55 PM		Displayed if the
No	CHANNEL	DATE	ON	OFF	MODE	DRIVE CHECK
							recording can fit
01	64 ABC	3/ 26 TUE	1:00 PM	2:00 PM	SP	Enable
02	64 ABC	3/ 26 TUE	2:30 PM	3:00 PM	SP	Enable	in the remaining
		New Timer Program					space	on	the
							disc.

≥Press [3, 4] to select “New Timer Program” and repeat steps 2- 4 to program other recordings.

5 Press [PROG/CHECK] or [RETURN].

The timer recording list disappears and the unit enters Timer Recording standby mode (“F” appears on the unit display).

≥The unit is not off. To save power, turn the unit off by press- ing [Í, DVD POWER].

To release the unit from recording standby

Cancel all the timer recording programs using [CANCEL]	recording
(➜ page 29).
To cancel recording when recording has
already begun
Press [∫], then [ENTER] within 5 seconds.	Timer
Recording stops.
[Note]

≥When the program timer reaches the set time when in record- ing standby mode, timer recording will start even if the unit is playing or recording another program.

≥The actual time recorded may be longer than the program itself when television programs are recorded using VCR Plusi.

≥If you don’t select a recording mode when using VCR Plus+ codes to make a timer recording, the unit sets the mode selected on the unit at that time (unless the mode is “XP”, in which case the unit sets “FR” as the mode).

≥“All timer programs are occupied.” appears if there are already 32 programs.

≥The remaining time displayed is based on the current record- ing mode.

≥When you program successive timer recordings to start immediately one after the other, the unit cannot record the part at the beginning of the later programs (a few seconds when recording with HDD or DVD-RAM, and approximately 30 seconds when recording with DVD-R).

≥If you set DST (Daylight Saving Time) to ON when manually setting the clock (➜ page 55), timer recording may not work when summer switches to winter and vice versa.

≥“F” flashes when the unit couldn’t go to timer recording standby.

≥When timer recording starts, the record lamp (➜ page 13, Main unit) lights, even if the unit is off.

Relief Recording

When the recording drive is set to “DVD” for timer recording, the unit will automatically evaluate if the program will fit onto the disc before beginning recording. If the program will not fit then the recording drive will be altered to “HDD” automatically.

≥If the time remaining on the HDD is insufficient, as much of the program as possible will be recorded onto the HDD.

≥If there is no disc in the tray or the disc cannot be recorded on, the recording drive will be altered to HDD.

≥The recording mode will not be altered.

≥The Direct Navigator shows which programs were relief- recorded (➜ page 19).

27

RQT6986