Sylvania DigitalVideoDiscRecorder Hints for Timer Recording, Priority of Overlapped Settings

Page 36

TIMER RECORDING

Hints for Timer Recording

•If there is a power failure or this unit has been unplugged for more than 30 seconds, the clock setting and all timer programming will be lost.

•If a disc is not inserted, flashes and timer recording cannot be performed. In some cases, will appear momentarily around the start point as the unit attempts to record. Please insert a recordable disc.

•When all the timer recording is completed, flashes. To play back or eject the recorded disc, press [POWER] first, then select the recorded title and press [PLAY B], or [OPEN/CLOSE A] to remove the disc.

•During timer recording or timer standby mode ( will appear), any operations on the unit will not be available. To make these operations available, press [STOP C] on the front panel to cancel the timer recording or [POWER] to release timer standby mode ( will disappear).

•To cancel the timer standby mode, press [POWER].

•When the starting and the ending time are the same, the length of the recording will be set for 24 hours. When the disc becomes full during the recording, the unit turns itself off.

•When the programmed starting and ending time are earlier than the current time, the setting will not be accepted and be cleared for redoing.

•If the starting time is earlier and the ending time is later than the current time, the recording will start right after you turn the power off.

The Priority of Overlapped Settings

•Timer program which has the earlier start time will be placed first in the timer program list, and be given priority over the programs with the later start time when timer programs overlap.

•When timer programs overlap, the first 2 minutes (at the longest) of the later recording will be cut off.

•When 2 or more timer programs have the same start time, the program set first will be given priority.

•A timer recording of lower priority will be canceled or start from the middle.

•Check the overlapped timer programmings and change the priority if necessary.

When the starting time is the same:

A program set previously (PROG. A) has priority.

PROG. A

PROG. B

actual recording

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PROG. A

 

 

PROG. B

 

 

 

 

The first 2 minutes (at the longest) will be cut off.

Note for DVD recording

•When the recording time of 2 programs are overlapped, or the end time of a program and the start time of another program is the same, the first 2 minutes (at the longest) of the subsequent program will be cut off.

•If the cut-off portion comes up to 3 minute or more, this program will be displayed with error number E40 in the timer programming list.

When the end time of the programming currently being recorded and the start time of the subsequent program are same:

The beginning of the PROG. B may be cut off.

PROG. A

 

 

PROG. B

 

 

actual

PROG. A

PROG. B

recording

 

 

The first 2 minutes (at the longest) will be cut off.

36 EN

Page 35 Page 37
Image 36
Page 35 Page 37
Contents ZC320SL8B Precautions Laser SafetyMake your contribution to the environment RADIO-TV InterferenceImportant Safeguards PrecautionsInstallation Location Supplied Accessories Avoid the Hazards of Electrical Shock and FireMoisture Condensation Warning About CopyrightMaintenance Servicing Cleaning the cabinetCleaning discs Cleaning the disc lens Disc handlingContents Features Features DVD-RUnplayable Discs Color SystemsRegion Codes DVD-VIDEO CD-DA CD-RWFunctional Overview Front PanelFunctional Overview Rear PanelRemote Control Installing the Batteries in the Remote ControlUsing a Remote Control Open the cover Insert batteriesTimer PROG. button Power buttonSetup button Zoom buttonFront Panel Display Display MessageWith the clock display Current status of the unitPlug in the power cords of the devices to the AC outlet Following the steps in Settings for the Video in RMake the connection as illustrated below Supplied cables used in this connection are as followsSettings for the Video Input Press Setup to exitIf you want to use S-VIDEO in jack, select S-Video Connection to a TV Connections BasicThis unit Audio OUT Video OUTConnection to AN Audio System AudioAudio OUT On-Screen Display / Menu OFFDisc Information/Menu Title Name Information File Name InformationGuide to ON-SCREEN Displays and Menus Main MenuInitial Setting Proceed to in Clock Setting onPress Enter to activate Clock Setting the Clock Clock SettingUse K / L to select calendar or time, then press Enter Formatting a Disc Choosing the Recording Format of a Brand-New DVD-RWIf you want to cancel formatting, select No Formatting a DiscReformatting a Disc Manually Formatting is completed.100% is indicatedSetting for Auto Chapter Setting Aspect Ratio for Video Mode RecordingPress Setup to exit Preparing a DiscSetting a Disc to Protect To cancel the disc protectOFF ON, then press ENTER. e.g. VR mode DVD-RW Use K / L to select Yes, then press EnterGeneral Setting menu will appear Your setting will be activatedAuto Finalizing Use K / L to select Recording, then press EnterPress Setup Use K / L to select DVD Menu, then press Enter Playing the Discs in Other DVD PlayersFinalizing a Disc Finalizing is completedTo cancel finalizing DVD-RW only Information on DVD Recording Recording SpeedRestrictions on Recording VideoPress Power Press OPEN/CLOSE a to close the disc trayPress REC Speed to select a recording speed It may take awhile to load Disc completelyPress Stop C to stop recording Press REC/OTR to start recordingWill be displayed for 5 seconds Timer Recording Press BUse K / L to enter the date, then Timer Recording Press Power to set a timer programmingTo exit, press Timer PROG. or Setup Use K / L to select a recordingTo stop the timer recording in process Press PowerPress Timer PROG. to exit Hints for Timer Recording Priority of Overlapped SettingsSatellite Link Use K / L to set the desired starting time, then press BSpeed Use K / L to select the recordingTo Standby Mode is highlighted Press Power to turn on the unitSatellite Link Press EnterConnection to an External Device External deviceSettings for AN External Device Recording from an External DeviceStructure of Disc Contents Information on PlaybackRefer to Using the Title/Disc Menu on Basic PlaybackDirect Playback Press Stop C once to stop playback temporarilyBasic Playback Playback from the Title ListUse K / L to select Play From Start, then press EnterJpeg pictures can also rotate by using K / L / / B Disc trayUsing the Title / Disc Menu PauseKodak Picture CD Special Playback Resume PlaybackFast Forward / Fast Reverse Playback Skipping TV Commercials During PlaybackSpecial Playback Rapid PlaybackStep by Step Playback Slow Forward / Slow Reverse PlaybackMarker Setting ZoomDVD-video Title track number and the time will be displayedUsing Skip j / Skip Using DisplaySearch Title/Chapter SearchSearch Time SearchAudio CD Repeat Playback Random PlaybackProgram Playback 5Press Play BSwitching Subtitles Switching Audio SoundtrackSwitching Virtual Surround System Switching Camera AnglesSelecting the Format of Audio and Video Reducing Block NoiseInformation on Disc Editing Guide to a Title ListDeleting Titles After the disc is fully recordedDeleting Titles CREATING/DELETING Playlist Adding Titles to a PlaylistCREATING/DELETING Playlist Erasing All PlaylistUse K / L to select Yes, then press ENTER.DVD Menu Main menu will appearEditing Discs Putting Names on TitlesUse K / L to select Edit Title Name, then press Enter Use K / L to select Edit, then pressEditing Discs Putting Names on Titles cont’dGuide to Edit Title Name Setting or Clearing Chapter Marks Use Skip H / GPress Return Submenu will appearDeleting a Part of a Title Deleting a Part of a Title cont’d Use K / L to select Delete then press EnterPart of the title is deleted For VR mode DVD-RW, press MENU/LIST to select Playlist Dividing a TitlePress Return or Stop C to exit You can divide one title into 2 new titlesCombining Titles Use K / L/ / B to select anotherCombining, then press Enter Title to combine, then press EnterSetting or Releasing the Title Protection To protect a whole disc VR mode DVD-RW onlyConfirm the indication OFF ON. Press Enter again Press Return and then Return or Stop C to exitSetting or Clearing All Chapter Marks at Once Use K / L to select Chapter MarkUse K / L to select the desired interval, then press Enter If you select OFF at , all the chapter marks are erasedList of Settings ContentsList of Settings 70 ENSetups PlaybackUse K / L to select a desired item Refer 1 to 7 on pages 72 to 74Setups Parental Lock Default AllUse the Number buttons to enter the current password Playback cont’dDisc Menu Language Default English Audio Language Default OriginalAudio Out PCMSubtitle Language Default OFF Angle Icon Default onStill Mode Default Auto Display Selection menu will appearOSD Language Default English Screen Saver Default 10 minutesFL Dimmer Default Bright Display cont’dWhen you finish with the setting, press Setup to exit VideoRefer 1 to 2 on page 78 and set the selected item For 3 , refer to Connection to an External Device onProgressive Default OFF TV Aspect Default 43 Letter BoxVideo cont’d Reset All Select Yes using K / L , then press EnterSelect Yes again using K / L , then press Enter Function SetupTroubleshooting Symptom RemedyTroubleshooting Recording / Timer recording / EditingStop C OPEN/CLOSE a to take out the disc. The disc canceled during Repairing process MAY not workOthers You press OPEN/CLOSE aError message Cause Solution Frequently Asked Questions Language Code Language CodeGlossary Specifications GeneralRecording TerminalsEspañol Discos no ReproduciblesCódigos de Región Disco simple de video VSDPresione Setup y utilice K / L EspañolUtilice K / L para seleccionar la Posición de la entrada externaPresione Power Presione Enter para activar Ajste Manual de RelojPresione REC/OTR para iniciar la grabación Para de tener la grabación presione Stop CPresione Timer Prog Configure una programación del temporizador Presione EnterAbra la bandeja Detenga laCustomer Service TelE7E2BUD 1VMN23640
Top Page Image Contents