BenQ MW82IST user manual Controls and functions

Page 10

Controls and functions

Projector

	1
		9
		8
	2	3
	2	10
	4	10
	4	11
	12	13
	5	14
	6	14
	6	11
	7	11
	7

1.	Focus ring	9.	POWER indicator light
	Adjusts the focus of the projected image.		Lights up or flashes when the projector is
2.	Top IR remote sensor		under operation.
3.	LAMP indicator light	10.	AUTO
	Indicates the status of the lamp. Lights up		Automatically determines the best picture
	or flashes when the lamp has developed a		timings for the displayed image.
	problem.	11.	Keystone/Arrow keys ( / Up,	/
4.	MENU/EXIT		Down)

Turns on the On-Screen Display (OSD) menu. Goes back to previous OSD menu, exits and saves menu settings.

5. Left/

Decreases the projector volume.

6.MODE/ENTER

Selects an available picture setup mode.

Activates the selected On-Screen Display (OSD) menu item.

7.ECO BLANK

Used to hide the screen picture.

8.TEMPerature warning light

Lights up red if the projector's temperature becomes too high.

Manually corrects distorted images resulting from an angled projection.

12. POWER

Toggles the projector between standby mode and on.

13. Right/

Increases the projector volume.

When the On-Screen Display (OSD) menu is activated, the #5, #11, and #13 keys are used as directional arrows to select the desired menu items and to make adjustments.

14.SOURCE

Displays the source selection bar.

10 Introduction

Image 10

Contents MW821ST Table of contents Important safety instructions Safety InstructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Projector features IntroductionShipping contents Projector exterior view Front/upper side Rear/lower sideControls and functions Remote control Remote control effective range Replacing the remote control batteriesFront Table Positioning your projectorChoosing a location Front CeilingProjection dimensions Obtaining a preferred projected image sizeConnection ConnectionConnecting audio Connecting video source devicesPlaying sound through the projector About the microphone input DeviceOperation Starting up the projectorAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image clarityCorrecting keystone Using the menus Below is the overview of the OSD menuSetting a password Using a security cable lockUtilizing the password function If you forget the passwordChanging the password Entering the password recall procedureDisabling the password function Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Setting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menuAdjusting Brilliant Color Fine-tuning the image quality in user modesSelecting a Color Temperature Setting a preferred color temperature 3D Color ManagementResetting current or all picture modes Setting the presentation timerSelection Description Freezing the image To cancel the timer, perform the following stepsRemote paging operations Top-Left Bottom-Left Top-Right Bottom-RightLocking control keys To activate the High Altitude ModeHiding the image Operating in a high altitude environmentUsing the test pattern Adjusting the soundTurning off the Power On/Off Ring Tone Using the teaching templates To select Blackboard or WhiteboardDirect power off Shutting down the projectorMenu system Menu operationMain menu Sub-menu Options Bottom-Right/Bottom-Left Sleep Timer Disable/30 min/1 hr/2 hr/3 hr/4 Hr/8 hr/12 hrBasic Min/25 min/30 minIP Address Main menu Sub-menu Options System Setup AdvancedEquivalent Lamp Hour Color SystemDescription of each menu Color Temperature Picture ModeTemperature Fine Tuning 3D ColorSettings TimerInstallation SearchRemote System Setup Basic menu Function DescriptionOperation ReceiverAudio System Setup Advanced menu Function Description HighAltitude LampStandby System Setup Advanced menu Function DescriptionReset All NetworkSystem CurrentStatus Maintenance Care of the projectorGetting to know the lamp hour Lamp informationExtending lamp life Timing of replacing the lamp Status MessageReplacing the lamp Connect the power and restart the projector Resetting the lamp timer Lamp events IndicatorsLight Status & Description Power events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Wall mount installationMinimum Ceiling Height mm = f + H + b + 60 + 274+ c Wall plateTiming chart Supported timing for PC inputSupported timing for Hdmi Hdcp input KHzSupported timing for Video and S-Video inputs Supported timing for Component-YP bP r inputTiming Copyright Warranty and Copyright informationLimited warranty Disclaimer