BenQ MW82IST user manual Magnifying and searching for details, Selecting the aspect ratio

Page 25

Magnifying and searching for details

If you need to find the details on the projected picture, magnify the picture. Use the direction arrow keys for navigating the picture.

•Using the remote control

1.Press Digital Zoom+/- to display the Zoom bar. Press Digital Zoom+ to magnify the center of the picture. Press the key repeatedly until the picture size is suitable for your need.

2.Use the directional arrows ( , , , ) on the projector or remote control to navigate the picture.

3.To restore the picture to its original size, press AUTO. You can also press Digital Zoom-. When the key is pressed again, the picture is further reduced until it is restored to the original size.

•Using the OSD menu

1.Press MENU/EXIT and then press / until the DISPLAY menu is highlighted.

2.Press to highlight Digital Zoom and press MODE/ENTER. The Zoom bar displays.

3.Press repeatedly to magnify the picture to a desired size.

4.To navigate the picture, press MODE/ENTER to switch to the panning mode and

press the directional arrows ( , , , ) on the projector or remote control to navigate the picture.

5.To reduce size of the picture, press MODE/ENTER to switch back to the zoom in/ out function, and press AUTO to restore the picture to its original size. You can

also press repeatedly until it is restored to the original size.

The picture can only be navigated after it is magnified. You can further magnify the picture while searching for details.

Selecting the aspect ratio

The “aspect ratio” is the ratio of the image width to the image height. Most analog TV and some computers are in 4:3 ratio, and digital TV and DVDs are usually in 16:9 ratio.

With the advent of digital signal processing, digital display devices like this projector can dynamically stretch and scale the image output to a different aspect than that of the image input signal.

To change the projected picture ratio (no matter what aspect the source is):

•Using the remote control

1.Press Aspect to show the current setting.

2.Press Aspect repeatedly to select an aspect ratio to suit the format of the video signal and your display requirements.

•Using the OSD menu

1.Press MENU/EXIT and then press / until the DISPLAY menu is highlighted.

2.Press to highlight Aspect Ratio.

3.Press / to select an aspect ratio to suit the format of the video signal and your display requirements.

Operation 25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents MW821ST Table of contents Safety Instructions Important safety instructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Introduction Projector featuresShipping contents Front/upper side Rear/lower side Projector exterior viewControls and functions Remote control Replacing the remote control batteries Remote control effective rangeChoosing a location Positioning your projectorFront Table Front CeilingObtaining a preferred projected image size Projection dimensionsConnection ConnectionConnecting audio Connecting video source devicesPlaying sound through the projector Device About the microphone inputStarting up the projector OperationAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image clarityCorrecting keystone Below is the overview of the OSD menu Using the menusUtilizing the password function Using a security cable lockSetting a password If you forget the passwordChanging the password Entering the password recall procedureDisabling the password function Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Selecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Go to the Picture Picture Mode menuAdjusting Brilliant Color Fine-tuning the image quality in user modesSelecting a Color Temperature 3D Color Management Setting a preferred color temperatureResetting current or all picture modes Setting the presentation timerSelection Description Remote paging operations To cancel the timer, perform the following stepsFreezing the image Top-Left Bottom-Left Top-Right Bottom-RightHiding the image To activate the High Altitude ModeLocking control keys Operating in a high altitude environmentUsing the test pattern Adjusting the soundTurning off the Power On/Off Ring Tone To select Blackboard or Whiteboard Using the teaching templatesShutting down the projector Direct power offMenu system Menu operationMain menu Sub-menu Options Basic Sleep Timer Disable/30 min/1 hr/2 hr/3 hr/4 Hr/8 hr/12 hrBottom-Right/Bottom-Left Min/25 min/30 minEquivalent Lamp Hour Main menu Sub-menu Options System Setup AdvancedIP Address Color SystemDescription of each menu Temperature Picture ModeColor Temperature Fine Tuning 3D ColorInstallation TimerSettings SearchOperation System Setup Basic menu Function DescriptionRemote ReceiverAltitude System Setup Advanced menu Function Description HighAudio LampReset All System Setup Advanced menu Function DescriptionStandby NetworkSystem CurrentStatus Care of the projector MaintenanceGetting to know the lamp hour Lamp informationExtending lamp life Status Message Timing of replacing the lampReplacing the lamp Connect the power and restart the projector Resetting the lamp timer Light Status & Description Power events IndicatorsLamp events Thermal eventsTroubleshooting Projector specifications SpecificationsWall mount installation DimensionsWall plate Minimum Ceiling Height mm = f + H + b + 60 + 274+ cSupported timing for PC input Timing chartKHz Supported timing for Hdmi Hdcp inputSupported timing for Video and S-Video inputs Supported timing for Component-YP bP r inputTiming Limited warranty Warranty and Copyright informationCopyright Disclaimer
Top Page Image Contents