BenQ MW82IST user manual Specifications, Projector specifications

Page 54

Specifications

Projector specifications

All specifications are subject to change without notice.

Optical

Resolution

1280 x 800 WXGA

Display system 1-CHIP DMD

Lens F/Number

F = 2.6, f = 6.9 mm Lamp

210 W lamp

Electrical

Power supply

AC100–240V, 3.5 A, 50-60 Hz (Automatic)

Power consumption

303 W (Max); < 0.5 W (Standby)

Mechanical

Weight

2.9 Kg (6.39 lbs)

Output terminals

RGB output

D-Sub 15-pin (female) x 1 Speaker

(Stereo) 10 watt x 1 Audio signal output

PC audio jack x 1

Control

RS-232 serial control 9 pin x 1

IR receiver x 2

LAN control RJ45 x 1

Input terminals

Computer input RGB input

D-Sub 15-pin (female) x 2

Video signal input

S-VIDEO

Mini DIN 4-pin port x 1

VIDEO

RCA jack x 1 SD/HDTV signal input

Analog - Component RCA jack x 3 (through RGB input)

Digital - HDMI x 1

Audio signal input Audio in

RCA audio jack (L/R) x 2 PC audio jack x 2 Microphone x 1

USB port (Mini-B x 1)

Environmental Requirements

Operating temperature 0°C–40°C at sea level

Operating relative humidity 10%–90% (without condensation)

Operating altitude 0–1499 m at 0°C–35°C 1500–3000 m at 0°C–30°C (with High Altitude Mode on)

54 Specifications

Image 54
Contents MW821ST Table of contents Important safety instructions Safety InstructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Projector features IntroductionShipping contents Projector exterior view Front/upper side Rear/lower sideControls and functions Remote control Remote control effective range Replacing the remote control batteriesFront Table Positioning your projectorChoosing a location Front CeilingProjection dimensions Obtaining a preferred projected image sizeConnection ConnectionConnecting video source devices Connecting audioPlaying sound through the projector About the microphone input DeviceOperation Starting up the projectorAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image clarityCorrecting keystone Using the menus Below is the overview of the OSD menuSetting a password Using a security cable lockUtilizing the password function If you forget the passwordEntering the password recall procedure Changing the passwordDisabling the password function Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Setting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Adjusting Brilliant ColorSelecting a Color Temperature Setting a preferred color temperature 3D Color ManagementSetting the presentation timer Resetting current or all picture modesSelection Description Freezing the image To cancel the timer, perform the following stepsRemote paging operations Top-Left Bottom-Left Top-Right Bottom-RightLocking control keys To activate the High Altitude ModeHiding the image Operating in a high altitude environmentAdjusting the sound Using the test patternTurning off the Power On/Off Ring Tone Using the teaching templates To select Blackboard or WhiteboardDirect power off Shutting down the projectorMenu operation Menu systemMain menu Sub-menu Options Bottom-Right/Bottom-Left Sleep Timer Disable/30 min/1 hr/2 hr/3 hr/4 Hr/8 hr/12 hrBasic Min/25 min/30 minIP Address Main menu Sub-menu Options System Setup AdvancedEquivalent Lamp Hour Color SystemDescription of each menu Color Temperature Picture ModeTemperature Fine Tuning 3D ColorSettings TimerInstallation SearchRemote System Setup Basic menu Function DescriptionOperation ReceiverAudio System Setup Advanced menu Function Description HighAltitude LampStandby System Setup Advanced menu Function DescriptionReset All NetworkCurrent SystemStatus Maintenance Care of the projectorLamp information Getting to know the lamp hourExtending lamp life Timing of replacing the lamp Status MessageReplacing the lamp Connect the power and restart the projector Resetting the lamp timer Lamp events IndicatorsLight Status & Description Power events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Wall mount installationMinimum Ceiling Height mm = f + H + b + 60 + 274+ c Wall plateTiming chart Supported timing for PC inputSupported timing for Hdmi Hdcp input KHzSupported timing for Component-YP bP r input Supported timing for Video and S-Video inputsTiming Copyright Warranty and Copyright informationLimited warranty Disclaimer