BenQ MW82IST Display menu Picture menu Function, Teaching, Template, Picture Mode, Reference

Page 40

1. DISPLAY menu

2. PICTURE menu

Function

Description

Teaching

See "Using the teaching templates" on page 34 for details.

Template

 

Picture Mode

Pre-defined picture modes are provided so you can optimize your

projector image set-up to suit your program type. See "Selecting a

 

picture mode" on page 27 for details.

Reference

Selects a picture mode that best suits your need for the image quality

and further fine-tune the image based on the selections listed on the

Mode

same page below. See "Setting the User 1/User 2 mode" on page 27

 

for details.

Brightness

Adjusts the brightness of the image. See "Adjusting Brightness" on

page 28 for details.

 

Contrast

Adjusts the degree of difference between dark and light in the image.

See "Adjusting Contrast" on page 28 for details.

 

 

Adjusts the color saturation level -- the amount of each color in a

Color

video image. See "Adjusting Color" on page 28 for details.

This function is only available when a Video, S-Video or Component Video

 

 

signal is selected.

 

 

 

Adjusts the red and green color tones of the image. See "Adjusting

Tint

Tint" on page 28 for details.

This function is only available when a Video or S-Video signal is selected and

 

 

the system format is NTSC.

 

 

 

Adjusts the image to make it look sharper or softer. See "Adjusting

Sharpness

Sharpness" on page 28 for details.

This function is only available when a Video, S-Video or Component Video

 

 

signal is selected.

 

 

Brilliant Color

See "Adjusting Brilliant Color" on page 28 for details.

 

 

Color

See "Selecting a Color Temperature" on page 28 for details.

Temperature

 

 

Color

 

Temperature

See "Setting a preferred color temperature" on page 29 for details.

Fine Tuning

 

 

 

3D Color

See "3D Color Management" on page 29 for details.

Management

 

 

 

Reset Picture

See "Resetting current or all picture modes" on page 30 for details.

Setting

 

40 Operation

Page 39 Page 41
Image 40
Page 39 Page 41
Contents MW821ST Table of contents Important safety instructions Safety InstructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Projector features IntroductionShipping contents Projector exterior view Front/upper side Rear/lower sideControls and functions Remote control Remote control effective range Replacing the remote control batteriesPositioning your projector Choosing a locationFront Table Front CeilingProjection dimensions Obtaining a preferred projected image sizeConnection ConnectionConnecting audio Connecting video source devicesPlaying sound through the projector About the microphone input DeviceOperation Starting up the projectorAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image clarityCorrecting keystone Using the menus Below is the overview of the OSD menuUsing a security cable lock Utilizing the password functionSetting a password If you forget the passwordChanging the password Entering the password recall procedureDisabling the password function Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Using Wall Color Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menuAdjusting Brilliant Color Fine-tuning the image quality in user modesSelecting a Color Temperature Setting a preferred color temperature 3D Color ManagementResetting current or all picture modes Setting the presentation timerSelection Description To cancel the timer, perform the following steps Remote paging operationsFreezing the image Top-Left Bottom-Left Top-Right Bottom-RightTo activate the High Altitude Mode Hiding the imageLocking control keys Operating in a high altitude environmentUsing the test pattern Adjusting the soundTurning off the Power On/Off Ring Tone Using the teaching templates To select Blackboard or WhiteboardDirect power off Shutting down the projectorMenu system Menu operationMain menu Sub-menu Options Sleep Timer Disable/30 min/1 hr/2 hr/3 hr/4 Hr/8 hr/12 hr BasicBottom-Right/Bottom-Left Min/25 min/30 minMain menu Sub-menu Options System Setup Advanced Equivalent Lamp HourIP Address Color SystemDescription of each menu Picture Mode TemperatureColor Temperature Fine Tuning 3D ColorTimer InstallationSettings SearchSystem Setup Basic menu Function Description OperationRemote ReceiverSystem Setup Advanced menu Function Description High AltitudeAudio LampSystem Setup Advanced menu Function Description Reset AllStandby NetworkSystem CurrentStatus Maintenance Care of the projectorGetting to know the lamp hour Lamp informationExtending lamp life Timing of replacing the lamp Status MessageReplacing the lamp Connect the power and restart the projector Resetting the lamp timer Indicators Light Status & Description Power eventsLamp events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Wall mount installationMinimum Ceiling Height mm = f + H + b + 60 + 274+ c Wall plateTiming chart Supported timing for PC inputSupported timing for Hdmi Hdcp input KHzSupported timing for Video and S-Video inputs Supported timing for Component-YP bP r inputTiming Warranty and Copyright information Limited warrantyCopyright Disclaimer
Top Page Image Contents