BenQ MW82IST user manual Using the menus, Below is the overview of the OSD menu

Page 21

Using the menus

The projector is equipped with On-Screen Display (OSD) menus for making various adjustments and settings.

The OSD screenshots below are for reference only, and may differ from the actual design.

Below is the overview of the OSD menu.

Main menu icon

Main menu

DISPLAY

Wall Color

Aspect Ratio

Keystone

Sub-menu

Position

Phase

H. Size

Digital Zoom

3D

Highlight

Teaching Template

Current input signal

Analog RGB

Off

Auto

ENTER

0

0

MENU Exit

Status

Press MENU/ EXIT to the previous page or to exit.

The following example describes how to set the OSD language.

1. Press MENU/EXIT on the projector or 3.	Press to highlight Language
remote control to turn the OSD menu on.	and press MODE/ENTER.

DISPLAY

Wall Color	Off
Aspect Ratio	Auto
Keystone
Position
Phase	0
H. Size	0
Digital Zoom
3D
Teaching Template
Analog RGB	MENU Exit

4.Press / / / to select a preferred language.

SYSTEM SETUP: Basic

Presentation Timer
Language	ENTER
Projector Installation	Front Table
Menu Settings
Operation Settings
Remote Receiver	Front+Top
Panel Key Lock	Off
Background Color	BenQ
Splash Screen	BenQ
PointDraw

Analog RGB

MENU Exit

2.Use / to highlight the SYSTEM SETUP: Basic menu.

SYSTEM SETUP: Basic

Presentation Timer
Language
Projector Installation	Front Table
Menu Settings
Operation Settings
Remote Receiver	Front+Top
Panel Key Lock	Off
Background Color	BenQ
Splash Screen	BenQ
PointDraw

5.Press MENU/EXIT twice* on the projector or remote control to leave and save the settings.

*The first press leads you back to the main menu and the second press closes the OSD menu.

Analog RGB	MENU Exit

Operation 21

Image 21

Contents MW821ST Table of contents Safety Instructions Important safety instructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Introduction Projector featuresShipping contents Front/upper side Rear/lower side Projector exterior viewControls and functions Remote control Replacing the remote control batteries Remote control effective rangeChoosing a location Positioning your projectorFront Table Front CeilingObtaining a preferred projected image size Projection dimensionsConnection ConnectionConnecting video source devices Connecting audioPlaying sound through the projector Device About the microphone inputStarting up the projector OperationAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image clarityCorrecting keystone Below is the overview of the OSD menu Using the menusUtilizing the password function Using a security cable lockSetting a password If you forget the passwordEntering the password recall procedure Changing the passwordDisabling the password function Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Selecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Adjusting Brilliant ColorSelecting a Color Temperature 3D Color Management Setting a preferred color temperatureSetting the presentation timer Resetting current or all picture modesSelection Description Remote paging operations To cancel the timer, perform the following stepsFreezing the image Top-Left Bottom-Left Top-Right Bottom-RightHiding the image To activate the High Altitude ModeLocking control keys Operating in a high altitude environmentAdjusting the sound Using the test patternTurning off the Power On/Off Ring Tone To select Blackboard or Whiteboard Using the teaching templatesShutting down the projector Direct power offMenu operation Menu systemMain menu Sub-menu Options Basic Sleep Timer Disable/30 min/1 hr/2 hr/3 hr/4 Hr/8 hr/12 hrBottom-Right/Bottom-Left Min/25 min/30 minEquivalent Lamp Hour Main menu Sub-menu Options System Setup AdvancedIP Address Color SystemDescription of each menu Temperature Picture ModeColor Temperature Fine Tuning 3D ColorInstallation TimerSettings SearchOperation System Setup Basic menu Function DescriptionRemote ReceiverAltitude System Setup Advanced menu Function Description HighAudio LampReset All System Setup Advanced menu Function DescriptionStandby NetworkCurrent SystemStatus Care of the projector MaintenanceLamp information Getting to know the lamp hourExtending lamp life Status Message Timing of replacing the lampReplacing the lamp Connect the power and restart the projector Resetting the lamp timer Light Status & Description Power events IndicatorsLamp events Thermal eventsTroubleshooting Projector specifications SpecificationsWall mount installation DimensionsWall plate Minimum Ceiling Height mm = f + H + b + 60 + 274+ cSupported timing for PC input Timing chartKHz Supported timing for Hdmi Hdcp inputSupported timing for Component-YP bP r input Supported timing for Video and S-Video inputsTiming Limited warranty Warranty and Copyright informationCopyright Disclaimer