Vivitek DVR5612 manual Before use OSD, You must know, Recommended ways to learn about operations

Page 20

How to use OSD

8

Before use OSD, You must know:

Recommended ways to learn about operations

Before starting, please follow the suggested steps to understand the fundamentals of operating the display, and then you will be able to learn the operations in a short time:

1.Please first learn to power on and power off the display. Refer to page 18 for the descriptions of the operations.

2.Please learn how to operate the OSD.

3.Understand what each OSD menu is. Refer to page 20~28 for an explanation of the OSD contents.

Example how to select correct input signal source.

After power on the display, first step: you need to select the correct input signal source. The screen will be blank without any images with incorrect input signal source. Follow the steps to set up:

1.Use OSD to select the correct input source, press the MENU key and bring up the OSD menu.

2.Use ▲▼ keys to select the “INPUT SETUP” option , press OK to enter the submenu.

Press OK to enter the Submenu

3.Then the OSD will show the Submenu as below:

4.Press OK , then press ◄ ► to change the main input source, last pressOK again to exit this main input setup.

Follow the OSD's indicate to operate the OSD. For example:

1.Use ▲▼ key to select the item "Main Input" , "PIP INPUT" or "INPUT SIGNAL"

2.then use OK to enter the item that you select.

eg: use ▲▼ to select MAIN INPUT, press ok then use

◄► to select input source TV, DTV....

3.If you want to exit the submenu, press EXIT on remote control to main menu or Menu key to exit OSD.

5.Now you understand:

Just to press the MENU key to show the OSD

And follow the OSD buttom line's information to operat the OSD. So you only need MENU, EXIT , OK, ▲▼ ◄► , ENTER these keys to control the whole OSD.

If you still have any question, please call our service center to help you.

Quick Input Source select way

	For Main Input
	Press the INPUT key in the front control panel or remote control repeatedly, the input signal mode will appear on
	the top left corner, please select correct input signal mode.(Refer to Input relative page 13~15,24) COMP1
	For PIP Input	19
	Please refer to page 24.	19
	Please refer to page 24.

Image 20

Contents Page Accessories Check FCC WarningMaintenance Maintenance for filterImportant Statement Clear methodsReplacement method of projection lamp Replacement ProcedureIndex Important StatementDisplay Modes Remote Control Correct viewingHandling Moisture CondensationSafety Instructions Warning and Caution Keep this device from high temperature or direct sunshine Do not touch the device and power cord while wetInstall this device in a flat and solid place Keep the ventilation grill freeDo not stand or sit on this device Keep heavy objects off this deviceBe sure to remove the plug by holding the power cord plug OUT Connecting and Checking the AntennaConnection with Antenna Cable Front Connector System ConnectionRear Connector DVD, Satellite, Cable etcStereo amplifier Speaker SystemRear Connector Introduction the Control Panel and Remote Control Lamp / Power Status VOL InputButton name Function VOLOperation status Machine status Lamp LED Power onPower off Example how to select correct input signal source Before use OSD, You must knowRecommended ways to learn about operations Quick Input Source select wayOSD explanation BrightnessColor TintColor Temperature For TV, AV, Comp input source modeFor RGB, DVI input source mode Noise ReductionAuto Config DefaultADC Phase ADC ClockSplit TransparencyPIP Close Caption Input SignalAnalog TV Setup Digital TV Setup Bass TrebleBalance SpeakerChange Access Code Confirm Access CodeTV Rating Mpaa RatingOSD Timeout Reset ALL SettingReset Lamp Timer OSD H PositionProgramming the universal remote control Device program codesAmplifier and tuner codes Cable set-top box codesCD Player codes Computer and Home automation codesDVD Player codes Receiver codesADC JBLManufacturer Satellite set-top box codesTV codes JCB KECKTV SSSCCE VCR codesMGA MEI HI-QKLH Searching for device codes Reassigning device buttonsTo search for a device code To reassign device buttonsTeaching the remote control new functions Using the universal remote controlTo teach the remote control a new function To access the OSD with the universal remote controlUsing picture-in-picture PIP mode Setting the sleep timerTo control PIP mode using the universal remote control To set the sleep timer using the universal remote controlRemote control will not accept the device program code TroubleshootingLED doesn’t blink when a button is pressed Miscellaneous Default PC Input ModeVideo Input Format Specifications SUBIf following situations Please check the following itemsError Codes States Power LED Lamp LED Status DescriptionLED Status Normal OperationAnnouncement Service Information and AnnouncementService Information Page Vivitek Corp Fremont Blvd Fremont, CA Tel 510 Efax 510