Vivitek DVR5612 manual Replacement method of projection lamp, Replacement Procedure

Page 4

Important Statement

1

Replacement method of projection lamp

Projection lamps are supplies and have life span. Please contact the resellers when the image turns dark or color gets deteriorated. When this happens, please replace it with a new projection lamp. If the projection lamp could not light up and have noise, the possible reasons are:

1.The life span for the projection lamp are ended or

2.Shutting down the TV right after the turn-on of power. At the moment, the temperature of projection lamp is too high and does not cool down to certain degree. Turn it on after a few minutes and it will work properly. or

3.The projection lamp does not connect correctly with the lamp cradle.

Replacement Procedure

Beware of the high temperature when replace the projection lamp.

Lamp

1.Loose the screw on lamp cover

Warning:

Eye damage may result from Directly viewing the light produced by the lamp used in this apparatus. Always turn off lamp before opening this cover.

2.Then loose the screw on lamp

3.Pull out the lamp directly

4.Then put the new lamp into this unit. (Follow the reverse the way you took it out.)

Caution: After taking the projection lamp out, do not place any metal substance into the lamp cradle. Do not touch the lamp cradle or it’s easy to get burned or cause fire.

Caution: Do not touch the glass surface of the new projection lamp because it possibly will affect the quality of resolution and decrease the life span of the projection lamp.

Caution: Make sure to screw the screws firmly in order to prevent the shaking of the lamp, which will result in poor connection.

Caution: Put the discarded used projection lamp in the packaging box of the new projection lamp and handle it with case and compliant to local regulation. Please do not have kids to access the discarded lamps to prevent any danger.

Image 4

Contents Page Accessories Check FCC WarningMaintenance Maintenance for filterImportant Statement Clear methodsReplacement method of projection lamp Replacement ProcedureIndex Important StatementDisplay Modes Remote Control Correct viewingHandling Moisture CondensationSafety Instructions Warning and Caution Keep this device from high temperature or direct sunshine Do not touch the device and power cord while wetInstall this device in a flat and solid place Keep the ventilation grill freeDo not stand or sit on this device Keep heavy objects off this deviceBe sure to remove the plug by holding the power cord plug Connection with Antenna Cable Connecting and Checking the AntennaOUT Front Connector System ConnectionRear Connector DVD, Satellite, Cable etcStereo amplifier Speaker SystemRear Connector Introduction the Control Panel and Remote Control Lamp / Power StatusVOL InputButton name Function VOLPower off Power onOperation status Machine status Lamp LED Example how to select correct input signal source Before use OSD, You must knowRecommended ways to learn about operations Quick Input Source select wayOSD explanation BrightnessColor TintColor Temperature For TV, AV, Comp input source modeFor RGB, DVI input source mode Noise ReductionAuto Config DefaultADC Phase ADC ClockPIP TransparencySplit Analog TV Setup Input SignalClose Caption Digital TV Setup Bass TrebleBalance SpeakerChange Access Code Confirm Access CodeTV Rating Mpaa RatingOSD Timeout Reset ALL SettingReset Lamp Timer OSD H PositionProgramming the universal remote control Device program codesAmplifier and tuner codes Cable set-top box codesCD Player codes Computer and Home automation codesDVD Player codes Receiver codesADC JBLTV codes Satellite set-top box codesManufacturer JCB KECKTV SSSMGA VCR codesCCE KLH HI-QMEI Searching for device codes Reassigning device buttonsTo search for a device code To reassign device buttonsTeaching the remote control new functions Using the universal remote controlTo teach the remote control a new function To access the OSD with the universal remote controlUsing picture-in-picture PIP mode Setting the sleep timerTo control PIP mode using the universal remote control To set the sleep timer using the universal remote controlLED doesn’t blink when a button is pressed TroubleshootingRemote control will not accept the device program code Video Input Format Default PC Input ModeMiscellaneous Specifications SUBIf following situations Please check the following itemsError Codes States Power LED Lamp LED Status DescriptionLED Status Normal OperationService Information Service Information and AnnouncementAnnouncement Page Vivitek Corp Fremont Blvd Fremont, CA Tel 510 Efax 510