Vivitek DVR5612 manual Device program codes, Programming the universal remote control

Page 30

Programming the universal remote control

9

The TV device button has been preset to work with your RPTV TV (program code 0080). You can program the remote control to work with as many as seven other devices.

To program the remote to control other devices:

1 Turn on the device.

2 Press the matching device button on the remote control.

3 Press and hold the SETUP button until the LED flashes twice.

4 Enter the programming code for the device and manufacturer. For a list of device programming codes, see“Device program codes” below. If the code is accepted, the LED flashes twice after the last digit is entered.

If the LED does not flash twice, repeat Steps 2 through 4 with the next code listed for the device and manufacturer.

Important

If there more than one code listed for the device and manufacturer, make sure that you try all the codes listed to find the one that works for the device.

5 Point the remote control at the device and press the POWER button. The device should turn off.

Tips & Tricks

If you cannot find your manufacturer in the device list or the program code does not work, you can use the remote control to search for the correct component code. See “Searching for device codes” on page 36.

Device program codes

Use the codes in the following tables to program the remote control to work with your existing audio and video devices.

Amplifier and tuner codes

Manufacturer

Program Code

Bose

0674

GE

0078

Harman/Kardon

0892

JVC

0331

Marantz

0892

Optimus

0395

Philips

0892

 

 

Manufacturer

Program Code

Polk Audio

0892

Realistic

0395

Sony

0689

Soundesign

0078

Victor

0331

Wards

0078

Yamaha

0354

 

 

Cable set-top box codes

Manufacturer

Program Code

ABC

0003, 0017

Americast

0899

Bell South

0899

General Instrument

0276, 0476, 0810

Goldstar

0144

Hamlin

0009, 0273

Jerrold

0003, 0276, 0476, 0810

Memorex

0000

Motorola

1106

Pace

0237

Panasonic

0107, 0000

Paragon

0000

 

 

Manufacturer

Program Code

Philips

0305, 0317

Pioneer

0144, 0533, 0877

Pulsar

0000

Quasar

0000

Regal

0273, 0279

Runco

0000

Samsung

0144

Scientific Atlanta

0017, 0477, 0877

Starcom

0003

Toshiba

0000

Zenith

0000, 0525, 0899

 

 

 

 

29

Image 30
Contents Page Accessories Check FCC WarningImportant Statement MaintenanceMaintenance for filter Clear methodsReplacement method of projection lamp Replacement ProcedureIndex Important StatementDisplay Modes Remote Control Correct viewingHandling Moisture CondensationSafety Instructions Warning and Caution Keep this device from high temperature or direct sunshine Do not touch the device and power cord while wetDo not stand or sit on this device Install this device in a flat and solid placeKeep the ventilation grill free Keep heavy objects off this deviceBe sure to remove the plug by holding the power cord plug Connecting and Checking the Antenna Connection with Antenna CableOUT Front Connector System ConnectionStereo amplifier Rear ConnectorDVD, Satellite, Cable etc Speaker SystemRear Connector VOL Introduction the Control Panel and Remote ControlLamp / Power Status InputButton name Function VOLPower on Power offOperation status Machine status Lamp LED Recommended ways to learn about operations Example how to select correct input signal sourceBefore use OSD, You must know Quick Input Source select wayColor OSD explanationBrightness TintFor RGB, DVI input source mode Color TemperatureFor TV, AV, Comp input source mode Noise ReductionADC Phase Auto ConfigDefault ADC ClockTransparency PIPSplit Input Signal Analog TV SetupClose Caption Digital TV Setup Balance BassTreble SpeakerTV Rating Change Access CodeConfirm Access Code Mpaa RatingReset Lamp Timer OSD TimeoutReset ALL Setting OSD H PositionAmplifier and tuner codes Programming the universal remote controlDevice program codes Cable set-top box codesCD Player codes Computer and Home automation codesADC DVD Player codesReceiver codes JBLSatellite set-top box codes TV codesManufacturer KTV JCBKEC SSSVCR codes MGACCE HI-Q KLHMEI To search for a device code Searching for device codesReassigning device buttons To reassign device buttonsTo teach the remote control a new function Teaching the remote control new functionsUsing the universal remote control To access the OSD with the universal remote controlTo control PIP mode using the universal remote control Using picture-in-picture PIP modeSetting the sleep timer To set the sleep timer using the universal remote controlTroubleshooting LED doesn’t blink when a button is pressedRemote control will not accept the device program code Default PC Input Mode Video Input FormatMiscellaneous Specifications SUBIf following situations Please check the following itemsLED Status Error CodesStates Power LED Lamp LED Status Description Normal OperationService Information and Announcement Service InformationAnnouncement Page Vivitek Corp Fremont Blvd Fremont, CA Tel 510 Efax 510