Loewe 23332507.020 manual Automatic programming, Station sorting

Page 11
ANT TV
ANT TV ANT SAT Connect/disconnect Back
Antenna cable(s) for: Antenna/cable (analogue) DVB-T
DVB-C
DVB-S
to antenna socket(s):
ANT TV
Connect antenna cable(s)
Initial installation

First installation

Automatic programming

Automatic programming of the TV set is started the first time you switch it on. Follow the menus.

9. You should receive a picture with sound with the settings previously made

(only for ASTRA 1 and HOTBIRD). Then press OK.

10. In the “Pre-programming“ menu, select the factory-set pre-programming to

programme the satellite stations quickly.

To ensure all stations that can be currently received are searched for and

OK

By pressing in one of the arrow directions, you can choose the

settings ...

... and confirm your settings by pressing OK. You then go to

saved, select “No“ at this point.

Symbol rates: The standard symbol rates 22000 and 27500 are preset.

If you would like to receive stations with different symbol rates, specify

OK

the next menu.

 

Back to the previous menu.

1. First you have to select the menu language.

2. By pressing the OK button, you can call the menu “Connect antenna cables(s)". If you want to receive digital stations via satellite, then choose “DVB-S“ - confirm using the yellow

coloured key. If you also want to

receive digital terrestrial stations (DVB-T), then select “DVB-T“. Also select “Antenna/cable (analogue)"

- this way the standard analogue stations can also be searched for and OK Proceed

saved. If you can receive digital stations from the cable network, then select “DVB-C“ using the yellow coloured key.

3.For the country-specific station sorting, enter the location.

4.If you have selected “DVB-T“, you then reach the menu “Antenna DVB-T“. If you use an active antenna, then select “yes (5V)”.

5.In the “Select satellite installation“ menu, make the selection that corresponds to your satellite antenna installation.

Note: If you have any questions on how your satellite antenna installation is configured and on the antenna settings, consult your antenna installer or your specialist dealer.

6.Select the satellite the antenna is directed at, such as ASTRA1. If you only receive one satellite ...

7.In the following menu, specify whether the station search should take place in the high and low band (“Yes“) or only in the low band (“No“).

Note: For most satellites, a station search is required in both bands.

8.For the low band and high band, the standard frequencies 9750 MHz (9.75 GHz) and 10600 MHz (10.6 GHz) are preset.

If your satellite antenna is equipped with an LNC (LNB) with a divergent oscillator frequency, specify the corresponding frequency for low and high band respectively. Note: The correct display of the received frequencies in the “TV menu – Settings – Channels – Manual adjustment“ depends upon this setting.

the corresponding values here using the numeric buttons on your remote

control.

11. Press OK to obtain an overview of the settings with which the automatic

programming is to take place.

12. Press the OK button again and the station search will start. The TV set

searches for, sorts and saves all the TV stations that can be received,

according to your settings and the antennas connected.

13. When the TV stations are saved, you will receive a corresponding message.

14. Press the OK button and the set then searches for the radio stations.

15. The TV set searches for, saves and sorts all radio stations which can be

received with your antenna system.

16. Then log on your video equipment, decoder and audio system using the

connection wizard and connect these to the TV according to the connection

diagram displayed. If you want to connect other equipment later, you can

find information as of page 30.

You can repeat the initial installation at any time, e.g. after moving house. Call the index using the INFO button (in the TV mode, if no menu is opened). Select the index item “Repeat initial installation“ (you will find this listed separately before the letter A). Press OK to start the initial installation.

Note: For DVB-T stations in UK the stations are tied to “Logical Channel Numbers” – “LCN” and sorted from 1-799. Digital stations without “LCN” are stored from 800 onwards. Analogue stations are stored from 1001.

Station sorting

Note: not with DVB-T stations in UK.

You can change the station sorting that was carried out automatically later at any time, see “TV menu – Settings – Channels – Change stations“.

11 -

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Operating instructions Contents Open index Remote control TV functionsDigital Recorder Station up Menu right Control unitsDisplay red = standby green = operation Only for sets with a Digital Recorder Call the menu Menu upAudio input left Connections to rear panelWelcome Set CleaningDisposal Packing and box10 cm For your safetyConnection First installationRemote control Use of the binders Using the common interface moduleSwitching on Handling the fabric hoseStation sorting Automatic programmingSelect a TV channel First installation Daily operationSwitching on/off Directing DVB-T antennaVia the station list With the P+/P- buttons on the remote controlWith the numeric buttons of the remote control Changing stationsExample of the menu operation Basics about the menu operationFor the info system OKSelect SettingsUse To go to the previous/next letter This is how to select the index itemFor the index Control like on a mobile phone keypadDirect control on TV set Setting the soundPicture settings Calling the index How the coloured keys work in TV modeOperating modes TV Show status displaySelect picture format Call timer overviewUnder Settings you will find the following functions Call additional functionsDVB subtitles Calling the CI module menu Installing new DVB softwareRemoving the CI module Inserting a new CI moduleImage+ menu Image+ demo modeImage+ Picture in picture PIP Operating modes PIPPosition of the PIP picture Setting the PIP typeSwitch to small PIP Functions in the PIP menuEPG Programme guide Using the EPGMark this by using OK Operating modes EPGSelecting providers and stations Switch on TV when markedProgramming recording for recorders EPG menuDisplaying teletext pages Operating modes TeletextAnalogue Teletext Selection with the coloured keysMenu Display teletext menu Programme timer recordingsTeletext menu Digital teletext operation only for UK device versionEPG Programme guide Operating modes RadioRadio Radio menuOperating additional equipment Login and connect equipmentConnecting video/DVD recorders Now you will see the playback from the connected AV device Video playbackCalling AV input via the station list Calling AV inputs in the AV selection AV Call AV selectionAudio output Audio Digital OUT Assignment of digital audio inputs and outputsAudio input Audio Digital Link cable Only required for TV as centre loud speakerDigital audio Component Video EURO-AV cableSound menu using the button, select Sound via and then TV Connecting other audio amplifiers or active speakersSet geometry Setting colour standardHdmi DVI connection VGA/XGA connectionOKSelect COMP. in sockets and use Component video connectionSound from PC or Set Top Box Log in the component/device in the connection wizardSetting the remote control using code entry Functions for Loewe VCR VV 8106, 8136 Using the RC3 remote control to operate a VCRRotating the TV set Setting the position of the TV set when switched offSelect Settings What to do, if Problem Possible cause RemedyThat they fall between 1 WiredDigital Link Plus does not function Replace the Euro-AV cableGeneral data Technical dataConnections Electrical dataAccessories Switzerland Service AddressesLoewe Codelist RC3 / Lista de códigos RC3VCR SAT /STB SAT TPS Cable Box STB
Top Page Image Contents