Loewe 23332507.020 First installation Daily operation, Directing DVB-T antenna, Switching on/off

Page 12

First installation

Daily operation

Directing DVB-T antenna

Note: not with DVB-T stations in UK.

If you use a room antenna to receive one or more DVB-T stations that have picture and sound interference, then you should change the location of where the antenna is set up.

To help you direct your antenna or to help you determine the most suitable location to set up the antenna, your TV set has a display for the signal quality

Switching on/off

Your TV is equipped with an eco-standby power supply unit. On standby, the power consumption drops to low power. If you want to save even more electricity, switch the set off with the mains switch. However, please bear in mind that EPG data (electronic programme guide) will be lost and programmed timer recordings will not be performed by the TV.

C/N and the signal strength Level.

Consult your specialist dealer to find out which channels and frequency bands (VHF or UHF) are used to broadcast the digital TV stations in your area.

On any one channel, several digital stations are broadcast.

Select a TV channel

1.

Call the “TV menu“ via the MENU button.

 

 

2.

Use

to select “Settings“, then use

to select the menu line

 

underneath.

 

 

 

3.

Select “Channels“, then use

to select the menu line underneath.

 

 

 

 

 

 

 

 

 

 

 

 

TV menu

 

 

INFO END

 

 

 

 

Settings

 

 

 

 

 

 

Channels

 

Parental lock Timer functions Language

 

 

 

 

Manual adjustment

...

 

 

 

 

 

 

 

 

 

4.

Select “Manual adjustment“ and call the menu using OK

 

(in UK, the manual adjustment does not work with DVB-T).

Manual adjustment

 

 

 

 

 

Signal source

DVB-T

DVB-C

Antenna/cable (analogue)

Channel

E 05

 

 

Frequency

177.50 MHz

 

 

Name

Test

 

 

Bandwidth

7 MHz

 

 

C/N 96

 

 

Level 99

 

 

 

 

 

 

 

 

 

 

 

 

END

5.

For digital stations, select “Signal source – DVB-T“.

6.

Use the numerical buttons to specify the corresponding channel number.

 

Depending on the channel selected and country, the system automatically

 

sets the corresponding bandwidth of 7 or 8 MHz. You should only change

 

the bandwidth under special circumstances - if the channel raster in your

)

)

OK

RADIO

Switching off

If the TV set is switched on, you can switch it to standby using the blue ON/OFF button on the remote control or by using the indicator field on the set. The red lamp on the TV set lights up. If the orange indicator lights up, a timer recording is being made, EPG data is being captured or radio operation without screen display is active.

Switching on the TV set

From standby, it is best to switch the set back on using the blue On/Off button or by using the numeric buttons of the remote control (1 – 99).

Or use the switch integrated in the indicator on the set. The green indicator on the TV set lights up.

Or switch on the TV set with OK, you can then see the station list and select a station.

Switch on the radio

With the RADIO button on the remote control or:

Switch on radio using R on the control ring of the TV set.

area is different from the standard.

When you receive a digital station, the system displays the signal quality

C/N via a bar/numeric value and the signal strength via Level. The

antenna‘s direction or position is best when the largest values possible are

displayed (long bar) for the signal quality and signal strength.

7. Direct the antenna so that the largest numerical value/bar size is reached.

8. If no signal is found in the channel set, you can start the frequency search

run by pressing the blue button within the band selected (VHF or UHF).

9. Check the other channels one after another on which digital stations are

broadcast terrestrially in your area.

For the weakest station, direct the antenna so that the maximum numerical

value/bar size is achieved.

10. After you position or direct the antenna, we recommend to search for all the

stations using the “Search wizard“

(TV menu – Settings – Channels – Search wizard).

)

If you switch off the TV set using the mains switch on the set, the indicator no longer lights up.

If the TV set is switched off via the mains switch, you have to switch it into the standby mode first via the mains switch and then switch it on using one of the above mentioned methods.

- 12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Operating instructions Contents Remote control TV functions Digital RecorderOpen index Control units Display red = standby green = operationOnly for sets with a Digital Recorder Call the menu Menu up Station up Menu rightConnections to rear panel Audio input leftWelcome Cleaning DisposalPacking and box SetFor your safety 10 cmFirst installation Remote controlConnection Using the common interface module Switching onHandling the fabric hose Use of the bindersAutomatic programming Station sortingFirst installation Daily operation Switching on/offDirecting DVB-T antenna Select a TV channelWith the P+/P- buttons on the remote control With the numeric buttons of the remote controlChanging stations Via the station listBasics about the menu operation Example of the menu operationOKSelect Settings For the info systemThis is how to select the index item For the indexControl like on a mobile phone keypad Use To go to the previous/next letterSetting the sound Picture settingsDirect control on TV set How the coloured keys work in TV mode Operating modes TVShow status display Calling the indexCall timer overview Under Settings you will find the following functionsCall additional functions Select picture formatDVB subtitles Installing new DVB software Removing the CI moduleInserting a new CI module Calling the CI module menuImage+ demo mode Image+Image+ menu Operating modes PIP Picture in picture PIPSetting the PIP type Switch to small PIPFunctions in the PIP menu Position of the PIP pictureUsing the EPG Mark this by using OKOperating modes EPG EPG Programme guideSwitch on TV when marked Programming recording for recordersEPG menu Selecting providers and stationsOperating modes Teletext Analogue TeletextSelection with the coloured keys Displaying teletext pagesProgramme timer recordings Teletext menuDigital teletext operation only for UK device version Menu Display teletext menuOperating modes Radio RadioRadio menu EPG Programme guideLogin and connect equipment Connecting video/DVD recordersOperating additional equipment Video playback Calling AV input via the station listCalling AV inputs in the AV selection AV Call AV selection Now you will see the playback from the connected AV deviceAssignment of digital audio inputs and outputs Audio input Audio DigitalAudio output Audio Digital OUT Only required for TV as centre loud speaker Digital audioComponent Video EURO-AV cable Link cableConnecting other audio amplifiers or active speakers Sound menu using the button, select Sound via and then TVSetting colour standard Hdmi DVI connectionVGA/XGA connection Set geometryComponent video connection Sound from PC or Set Top BoxLog in the component/device in the connection wizard OKSelect COMP. in sockets and useSetting the remote control using code entry Using the RC3 remote control to operate a VCR Functions for Loewe VCR VV 8106, 8136Setting the position of the TV set when switched off Select SettingsRotating the TV set Problem Possible cause Remedy What to do, ifWired Digital Link Plus does not functionReplace the Euro-AV cable That they fall between 1Technical data General dataElectrical data ConnectionsAccessories Service Addresses SwitzerlandCodelist RC3 / Lista de códigos RC3 LoeweVCR SAT /STB SAT Cable Box STB TPS
Top Page Image Contents