Loewe 32959022 manual Connecting devices to the PC in connection and playback

Page 39

Operating additional equipment

Connecting devices to the HDMI (DVI) connections and playback

The HDMI connections (High Definition Multimedia In- terface) permit digital video and audio transmission via a connection cable from a player, e.g. from the Loewe

ViewVision DVD recorder.

The digital picture and sound data are transmitted without data compres- sion and therefore lose none of their quality.

Using a DVI/HDMI adapter cable, the digital video signals of a DVI player can also be played via the compatible HDMI connection. The sound must be fed in additionally.

HDMI and DVI both use the same copy protection method HDCP.

Connecting the device

Connect the device by an HDMI cable (type A, 19 pole) to the HDMI1/DVI or HDMI2/DVI socket of the TV set.

If a DVI/HDMI adapter cable is used, the appropriate sound can be fed in via the audio input socket AUDIO IN1 (analogue) or AUDIO DIGITAL IN (digital) on the TV set. See also page 47.

It is not necessary to log in HDMI devices in the connection wizard.

Playback from the device

Call AV selection.

VGA

AV selection

 

HDMI2/DVI COMP. IN

VIDEO VCR DVD

HDMI1/DVI

OK

34Select HDMI1/DVI or HDMI2/DVI socket, OK to switch over.

Start playback on the connected HDMI device.

The best possible format for the picture will be detected and set automatically.

Digital Link HD in appropriately equipped HDMI devices

As long as HDMI is selected as a memory location, all remote control commands which the connected HDMI unit can handle are passed on to it. Volume, Sound on/off, Sound adaptation and Picture format affect the operation of the TV set. The HDMI unit can therefore be installed in a concealed position and still be operated.

Switch back to TV mode to the station last viewed with the TV button. Switch Digital Link HD on/off temporarily: Press the TV button for a little longer (approx. 1 second).

TV remote switch on via HDMI

In the TV menu under Connections Miscellaneous Remote TV switch on via HDMI you can define that the TV set switches on automatically from standby when a connected HDMI device displays a menu or a disk is inserted.

Connecting devices to the PC IN connection and playback

You can connect a PC or a SetTopBox (STB) to the PC IN socket and thus use the screen of the TV set as an output device.

When connecting the TV set to a PC, first set your PC to one of the following screen resolutions:

800 x 600 60

Hz

(SVGA)

1024 x 768

60 Hz

(XGA)

1280 x 1024 60

Hz

(SXGA)

1360 x 768

60 Hz

(WXGA)

When connecting a SetTopBox set the following screen resolutions according to the possibilities of the SetTopBox:

SDTV:

720 x 576i

720 x 480i

 

720 x 576p

720 x 480p

HDTV:

1280 x 720p

1920 x 1080i

Connecting the device

Connect the device to the PC IN socket of the TV set via the VGA cable. See page 40 for the sound connection.

Registration in the connection wizard is not necessary.

Playback from the device

Call AV selection.

 

AV selection

 

 

 

 

 

AVS

PC IN

OK

HDMI1/DVI

HDMI2/DVI

COMP. IN

VIDEO

34Select PC IN socket, OK to switch over.

Adapting the geometry (only possible with certain signals)

This is where the picture can be properly positioned and the position of the picture (horizontal and vertical) can be moved so that it fills the entire screen.

Call TV menu.

34Selecting and adjusting the Geometry.

Setting the colour standard (only possible with certain signals) Call TV menu.

34Select Picture,

6 go to the menu line below.

34Select and set colour standard:

for PCs: RGB,

für STB: Ycc (rare: Ypp or RGB)

If the wrong standard is set then the colours will not be displayed correctly.

39 -

Image 39
Contents Operating instructions Contents Remote Control TV Functions Display Control unit front side of the deviceOn/Off button Button MFactory settings Connections rear side of the deviceSD/HD-COMPONENT in Cb/Pb-Cr/Pr-Y component video inputs Welcome Operating convenience with wizards Wizards in overviewInfo display and TV index Proper use and environmental conditions For your safetyPower supply Air circulation and high temperaturesSupervision Repairs and accessoriesVolume CleaningConnecting the TV set Initial installationInstalling the TV set Preparing the remote control unitTurning the set on/off First installation wizardDVB-S line Antenna/cable analogue analogue stations viaCall TV menu Explanation of the setting possibilitiesPositioning/aligning DVB-T antenna Explanations of the DVB-T antennaOperating convenience General information on menu operationInfo display Assist+ menu Index in the TV setTV menu Overview diagram Parental lock Timer functionsLanguage Miscellaneous Select provider Station selection Data capture Radio menu Overview diagramSwitch on TV when marked Newsflash Reveal Switch on TV when marked SettingsSelect station Daily operationSelect video source Adjusting the sound Operation without remote control Adjusting the pictureButton functions Yellow button Time selection Blue button Explanations of the symbols for sound identificationStatus display Additional selection possibilities for DVB stationsTV stations Search/update stations Search wizardExplanations of some search settings Managing stationsInput of the station colour standard Search/update station manual searchGo to the menu line below 34Select Stations Station3456or numeric buttons Change, delete, move, rename, restore stationsRestore stations Green button Starts Restore stationsPut together / change favourites lists Picture in Picture PIP Picture in PictureConfigure Picture in Picture PIP mode Electronic Programme Guide EPG Electronic Programme GuideConfiguring EPG Teletext TeletextDigital Teletext MHEG-5 Teletext menuConditional Access Module CA module Software update Radio Radio modeCall TV menu 34Select Connections Connecting additional devices to the TV setOperating additional equipment Device connection wizardManual recorder station search Explanations of important settingsConnecting antenna to the DVD/video recorder Connection possibilities for a DVD/video recorderConnecting devices to the PC in connection and playback OK calls the wizard Digital audio signalSockets 34Select New devices/modificationsIntegrated Dolby Digital Decoder Sound components wizardSetup ConnectingSwitch off all devices before connecting Adjusting the speaker system 34Select Configuration/modification Distance to left front speaker OK continue to Adjust speaker levelOK continue to Subwoofer phase OK continue to setConnecting analogue audio amplifiers Connecting audio amplifiersExplanations of the setting possibilities Connecting digital audio amplifiersAssignment of the digital audio input Audio connection in Hdmi DVI devicesRS-232C interface Direct way to record Timer recording with external devices Viewing photos PhotoViewerStarting the PhotoViewer Ending the PhotoViewerCalling the PhotoViewer menu Open folderMarking photos for slide show Starting a slide showOperating Loewe equipment Functions for the Loewe DVD player Auro 2216 PS, 8116 DT ViewVision DR+ Timeshift ModeRotating the TV set Troubleshooting Button Connection diagramWith Teletext various character sets are AmplifierConnections Technical dataGeneral data Electrical dataAccessories AccessoriesSetup possibilities CI slot See Common Interface Conditional Access Module See CA moduleGlossary Cinch cable Cable for transmitting audio or videoJPG See Jpeg LCD Liquid Crystal DisplayPicture in Picture see PIP HD digital TV analogueTV digital HD analogueIndex Palmer Street Service