Panasonic NV-MV40GL specifications To Play Back a Recorded Part Repeatedly, Ntsc Playback

Page 11

Playback

Preparations

Confirm that the VCR is on.

Confirm that the TV is on and the VCR viewing channel is selected.

Insert a recorded video cassette.

Set [VCR/TV] switch (22) to [VCR].

For Normal Playback:

Press [Play] (25).

For Cue or Review Playback:

During playback, tap [Fast Forward] (24) or [Rewind] (8).

• To return to normal playback, press [Play] (25).

• If you press and hold down [Fast Forward] (24) or [Rewind] (8), cue or review playback continues for as long as you keep the button pressed, and operation returns to normal playback when the button is released.

For High speed Cue or Review Playback (JET SEARCH): During playback, tap [Fast Forward] (24) or [Rewind] (8)

twice.

For Still Playback:

During playback, press [Pause/Slow] (28).

• To return to normal playback, press [Play] (25) or [Pause/Slow] (28).

For Slow Playback:

During playback, keep [Pause/Slow] (28) pressed for 2 seconds or more.

• To return to normal playback, press [Play] (25).

Fast-forwarding or Rewinding the Tape:

Press [Fast Forward] (24) or [Rewind] (8) in the stop mode.

• To stop fast-forwarding or rewinding, press [Stop] (9).

To Obtain a Higher Speed Rewind (Jet Rewind):

Press [JET REW] (26).

The [J . REW] indication appears on the TV screen and VCR displays channel position (except when the remaining tape time indication appears).

Depending on a cassette or an operating condition, the rewind speed may change somewhat.

The tape counter is reset to [0:00.00] when the tape is rewound to the beginning.

To Stop Playback

Press [Stop] (9).

Notes:

JET SEARCH, cue, review or slow playback will be automatically cancelled after 10 minutes, and still playback after 5 minutes.

During playback function other than normal playback, horizontal noise bars may appear in the picture, the colour of the picture may be unstable, or the picture may be otherwise distorted.

When you play back a tape recorded in the LP mode, the picture may be in black and white.

When you play back a tape recorded in the EP mode, the picture and the sound may be unstable.

However, these are not malfunctions.

To Play Back a Recorded Part Repeatedly

Press [REPEAT] (34). The [R] indication appears on the VCR display.

• A recorded part on the tape must be at least 15 minutes long.

• When recording over the same location on a tape, it may not function correctly.

To Cancel the Repeat Playback Mode:

Press [Stop] (9).

NTSC Playback

Tapes recorded in the NTSC system can be played back with this VCR via a PAL system TV.

Select [NTSC PB SELECT] from the On Screen Display according to the colour TV system of the TV. (See page 10.)

NTSC 3.58 recording requires [NTSC INPUT SELECT] to be in the AUTO or 3.58 position (see page 10), however if [NTSC INPUT SELECT] is in this position when recording a NTSC 3.58 signal, no colour is available for the PAL TV. Once the recording is completed, you then need to select [on PAL TV] to view the recording in colour on PAL TV.

On some TVs, the playback picture may roll up or down. If your TV has V-HOLD control or equivalent adjustment function, use it to adjust the picture.

Note for only NTSC Playback on PAL system TV

This function is designed to allow only the playback of tapes recorded by NTSC signals on a PAL system TV. The NTSC signal is not completely converted to a PAL signal. For this reason, images play back by this function cannot be recorded correctly on other VCRs.

11

Image 11
Contents Video Cassette Recorder ContentsCondensation may form in the following cases For your safetyInserting Remote Control Batteries 5453 Controls and ComponentsPROG/CHECK Picture ModeTimer Check Prog Guide Prog PlayBasic Connections Setting the Remote Control to Operate Your TVConnection to a TV using the Audio/Video Input Socket ConnectionsOperations Hold down Menu 7 for 5 seconds or more Tuning the TV to Your VCRTo Change the RF output Channel Press MenuPre-programmed TV Channels Australia only Auto Tuning Using the On Screen Display For AustraliaAuto Tuning Using the On Screen Display For New Zealand Storing TV Broadcasts in Your VCRSetting the Clock of Your VCR To Set the Colour TV System Settings Using the On Screen DisplayTo Make Various Indicators Appear On Screen Display OSD REC Option SettingTape Select JET NavigatorNtsc Playback PlaybackTo Play Back a Recorded Part Repeatedly Recording To Stop the OTR Recording Before the End To reset the tape counterTo Display the Approximate Remaining Tape Time Mode Recording from an external sourceRecording VCR VCR in tape refresh standbyKey Programming Timer RecordingDaily Timer Recording To Suspend the Timer Recording Standby ModeSetting other Programmes in Succession Weekly Timer RecordingPress PROG/CHECK 14 twice Checking a Timer ProgrammeCancelling a Timer Programme Icon indications Category setting allows you toTo Set the Category Recorded by the characterTo Check the Recorded Programming Data Time Stamp Function When Recording Over the Same Location on a TapeTo Cancel the Index Search or to Stop Playback Press Stop To Demonstrate the Jet Navigator FunctionMessage of On Screen Display Before Requesting ServiceTo Cancel the Easy Programme Playback Operation Press Prog PlayDirt on the video heads Adjusting the Playback PictureCrystal View Control Specifications