Panasonic NV-MV40GL Setting the Remote Control to Operate Your TV, Basic Connections

Page 5

Setting the Remote Control to Operate Your TV

You can operate the TVs of the manufacturers listed below with the remote control after setting it.

This setting procedure allows you to operate the TVs of some manufacturers using the supplied remote control.

Preparation

• Set [VCR/TV] switch (22) to [TV].

Operations

1Find the manufacturer number of your TV while referring to the following table.

2While holding down [TV-ON/OFF] (1) on the remote control, use [Numeric] (2) to enter the manufacturer number. This completes the settings for the TV manufacturer.

Be sure to enter the number in two digits. Example: 1 ) 01

3To confirm the correct settings were made, check whether the TV can be operated properly.

When a manufacturer has multipled numbers in the following table, try entering other numbers if the TV operations cannot be performed properly, and then select the optimal number.

Notes:

If you are using a Panasonic TV, this setting has already been made, and so you do not need to perform the above setting procedure. However, this remote control may not work with some Panasonic TVs.

Some TV models cannot be operated using this remote control (including all TVs non-remote compatible).

List of TVs Compatible with the VCR Remote Control

[Brand]

[Code]

 

 

Panasonic/National

01-04

 

 

SONY

05

 

 

TOSHIBA

06

 

 

JVC

07

 

 

HITACHI

08

 

 

MITSUBISHI

09, 10

 

 

SHARP

11

 

 

PHILIPS, SAMSUNG

12

 

 

NEC

13

 

 

SANYO

14

 

 

GOLDSTAR/LG

15, 16

 

 

SAMSUNG

17,18

 

 

SANYO

19

 

 

Connections

This section shows you how to connect the VCR to an aerial, TV, etc.

Basic Connections

The following connections are required to record and play back the video cassette through the TV.

 

 

(1)

 

(3)

(2)

 

 

(4)

 

AC IN ~

2 IN

 

 

(6)

VIDEO2

 

AUDIO2

2 OUT

 

IN (AV1) OUT

RF

 

 

(5)

 

¢

 

(1) Aerial (Not supplied)

(6) AC Input socket (48)

(2) TV Set (Not supplied)

¢ To mains supply

(3)Aerial Connector

(4)RF IN socket (51)

(5)RF OUT socket (52)

Connection to a TV using the Audio/Video Input Socket:

Set the RF output channel of the VCR to [ss] (RF OFF) when the VCR is connected to the TV via the Audio/Video cable. (See page 6.)

 

 

 

 

(1)

 

 

(3)

(2)

 

 

 

(4)

(5)

 

 

 

 

(6)

(7)

 

 

 

 

 

AC IN ~

 

2 IN

 

 

 

 

 

 

(10)

VIDEO2

 

 

 

AUDIO2

2 OUT

 

 

 

IN (AV1) OUT

RF

 

 

 

(9)

 

(8)

 

 

 

 

 

¢

 

 

 

(1)

Aerial (Not supplied)

 

(8) RF OUT socket (52)

 

(2)

TV Set (Not supplied)

 

(9) VIDEO OUT (50)/

 

(3)

Aerial Connector

 

AUDIO OUT (53)

 

(4)

VIDEO IN

 

(10)AC Input socket (48)

 

(5)

AUDIO IN

 

¢ To mains supply

 

(6)Audio Cable/Video Cable (Not supplied)

(7)RF IN socket (51)

5

Image 5
Contents Video Cassette Recorder ContentsCondensation may form in the following cases For your safetyInserting Remote Control Batteries 5453 Controls and ComponentsTimer Check Prog Guide Picture ModeProg Play PROG/CHECKConnection to a TV using the Audio/Video Input Socket Setting the Remote Control to Operate Your TVConnections Basic ConnectionsTo Change the RF output Channel Tuning the TV to Your VCRPress Menu Operations Hold down Menu 7 for 5 seconds or moreAuto Tuning Using the On Screen Display For New Zealand Auto Tuning Using the On Screen Display For AustraliaStoring TV Broadcasts in Your VCR Pre-programmed TV Channels Australia onlySetting the Clock of Your VCR To Set the Colour TV System Settings Using the On Screen DisplayTo Make Various Indicators Appear On Screen Display Tape Select Option SettingJET Navigator OSD RECNtsc Playback PlaybackTo Play Back a Recorded Part Repeatedly Recording To Stop the OTR Recording Before the End To reset the tape counterTo Display the Approximate Remaining Tape Time Recording VCR Recording from an external sourceVCR in tape refresh standby ModeKey Programming Timer RecordingSetting other Programmes in Succession To Suspend the Timer Recording Standby ModeWeekly Timer Recording Daily Timer RecordingPress PROG/CHECK 14 twice Checking a Timer ProgrammeCancelling a Timer Programme To Set the Category Category setting allows you toRecorded by the character Icon indicationsTo Cancel the Index Search or to Stop Playback Press Stop When Recording Over the Same Location on a TapeTo Demonstrate the Jet Navigator Function To Check the Recorded Programming Data Time Stamp FunctionTo Cancel the Easy Programme Playback Before Requesting ServiceOperation Press Prog Play Message of On Screen DisplayDirt on the video heads Adjusting the Playback PictureCrystal View Control Specifications