Panasonic NV-MV40GL specifications Setting the Clock of Your VCR

Page 8

Manual Tuning Procedure

1

Press [MENU] (7) to display the Main menu on the TV

 

screen.

2

Press [Cursor] (37) (34) to select [TUNER PRESET]

 

then press [OK] (23).

3

Press [Cursor] (37) (34) to select [CH] then select the

 

channel number you want to tune by pressing [Cursor]

 

(37) (21).

4

Confirm that [CLEAR] is set to [OFF].

5

Press [Cursor] (37) (34) to select [SEARCH] then

Setting the Clock of Your VCR

In the event of a power failure, the clock will operate on its back up system for a minimum of 3 years. After 3 years, clock back up in the event of a power failure can only be guaranteed for maximum of 1 hour.

Preparations

Confirm that the TV is on and the VCR viewing channel is selected.

Turn on the VCR.

press [Cursor] (37) (21) to start the Manual Tuning.

• If the desired TV station has not been tuned, press

[Cursor] (37) (21) again.

• Press [MENU] (7) and repeat steps 3-5for each

programme position you want to tune to a station.

CH 2

SEARCH

CH 2

SEARCH 74

 

END: MENU

 

 

 

END: MENU

 

 

 

 

• Example:

Date; 16 October, 2005

Time; 20:15

Operations

1Press [MENU] (7) to display the Main menu on the TV screen.

MENU

CLOCK SET TUNER PRESET SYSTEM OPTION

SELECT : , OK

END :MENU

6Press [MENU] (7) three times to exit the On Screen Display.

Direct Tuning

Follow steps 1 to 3 of Manual Tuning Procedure.

4

Confirm that [CLEAR] is set to [OFF].

5

Press [Cursor] (37) (34) select [SEARCH].

6

Press [Numeric] (2) to enter the number of the desired

 

programme position.

2Press [Cursor] (37) (34) to select [CLOCK SET] then press [OK] (23).

3Set each item by pressing [Cursor] (37) (341). Press

[Cursor] (37) (2) to return to the previous item.

MENU

CLOCK SET

TUNER PRESET

SYSTEM

OPTION

SELECT : , OK

END :MENU

 

CLOCK SET

 

Y

M

D

H:M

2005

1

1

0:00

SELECT:

START:MENU

• For other channels that require tuning, repeat steps 3-6.

7 Press [MENU] (7) twice to exit the On Screen Display.

Fine Tuning Procedure

Follow steps 1 to 3 of Manual Tuning Procedure.

4Press [Cursor] (37) (34) to select [FINE] then press [Cursor] (37) (21) to obtain the best tuning condition.

• Press [OK] (23) to return the tuning to its former state.

CH 2

 

 

 

AFC: OK

FINE

 

:

 

END: MENU

 

 

 

 

 

 

5 Press [MENU] (7) to exit the On Screen Display.

Blanking of Unused Programme Positions

Follow steps 1 to 3 of Manual Tuning Procedure.

4Press [Cursor] (37) (34) to select [CLEAR] then press [Cursor] (37) (21) to select [ON].

Repeat steps 3-4for other unused programme positions to skip during the selection of programme positions.

To cancel the blanking of a programme position select that programme position then set [CLEAR] to [OFF].

5Press [MENU] (7) twice to exit the On Screen Display.

At the set time (H:M) point:

When it is kept pressed, the indication changes in 30 minute steps.

There is no need to press [Cursor] (37) (1).

4 Press [MENU] (7).

• The clock starts.

Time Reset Function

If the clock is less than two minutes slow or fast, it can easily be reset to the proper time.

Example:

Resetting the clock to 12:00.00

1Press [MENU] (7) to display the Main menu on the TV screen.

2Press [Cursor] (37) (34) to select [CLOCK SET] then press [OK] (23).

3When the current clock displays on the VCR is between 11:58.00 and 12:01.59, press [MENU] (7) as soon as you hear the 12:00.00 signal. This resets the time to 12:00.00.

8

Image 8
Contents Contents Video Cassette RecorderCondensation may form in the following cases For your safetyInserting Remote Control Batteries Controls and Components 5453Picture Mode Timer Check Prog GuideProg Play PROG/CHECKSetting the Remote Control to Operate Your TV Connection to a TV using the Audio/Video Input SocketConnections Basic ConnectionsTuning the TV to Your VCR To Change the RF output ChannelPress Menu Operations Hold down Menu 7 for 5 seconds or moreAuto Tuning Using the On Screen Display For Australia Auto Tuning Using the On Screen Display For New ZealandStoring TV Broadcasts in Your VCR Pre-programmed TV Channels Australia onlySetting the Clock of Your VCR To Set the Colour TV System Settings Using the On Screen DisplayTo Make Various Indicators Appear On Screen Display Option Setting Tape SelectJET Navigator OSD RECNtsc Playback PlaybackTo Play Back a Recorded Part Repeatedly Recording To Stop the OTR Recording Before the End To reset the tape counterTo Display the Approximate Remaining Tape Time Recording from an external source Recording VCRVCR in tape refresh standby ModeTimer Recording Key ProgrammingTo Suspend the Timer Recording Standby Mode Setting other Programmes in SuccessionWeekly Timer Recording Daily Timer RecordingPress PROG/CHECK 14 twice Checking a Timer ProgrammeCancelling a Timer Programme Category setting allows you to To Set the CategoryRecorded by the character Icon indicationsWhen Recording Over the Same Location on a Tape To Cancel the Index Search or to Stop Playback Press StopTo Demonstrate the Jet Navigator Function To Check the Recorded Programming Data Time Stamp FunctionBefore Requesting Service To Cancel the Easy Programme PlaybackOperation Press Prog Play Message of On Screen DisplayDirt on the video heads Adjusting the Playback PictureCrystal View Control Specifications