Panasonic NV-MV40GL Tuning the TV to Your VCR, To Change the RF output Channel, Press Menu

Page 6

Tuning the TV to Your VCR

The VCR supplies a signal to the TV via the RF coaxial cable on channel AU28-69 or NZ21-69.

It is possible to view the video picture on your TV in the same way that you watch TV broadcasts.

If you have connected the VCR to the TV through the Audio/ Video input sockets, then you do not need to follow the procedure below.

Preparation

• Turn on the TV and the VCR.

Operations

1Hold down [MENU] (7) for 5 seconds or more.

2Set the TV to an unused position which you wish to use for your video playback.

• Tune the TV until the display

shown on the right appears on

the screen. (Please refer to the

Panasonic

VCR

 

 

 

 

 

TV manufacturers operating

 

 

 

 

 

 

 

 

 

 

instructions regarding tuning.)

 

 

 

END: MENU

3 Press [MENU] (7).

 

 

 

 

 

To Change the RF output Channel

In some rare cases after tuning the TV to your VCR, interference may be visible on the picture. To get rid of this interference, you can manually adjust the RF output channel a few channels up and down from the current setting. The procedure is described below.

Operations

1Hold down [MENU] (7) for 5 seconds or more.

The VCR display changes as shown below and the VCR picture on the TV displays this pattern.

Panasonic VCR

END: MENU

2Enter the desired channel number (AU28-69, NZ21-69) by [Numeric] (2) or [Channel] (32).

Ensure that [VCR/TV] switch (22) is set to [VCR].

Set the RF output channel of the VCR to [ss] (RF OFF) when the VCR is connected to the TV via the Audio/Video cable.

Press [Channel] (32) to display [ss].

For New Zealand

For Australia

21E 69E

28 37 69

 

(Initial position)

ss

(RF OFF)

It is also possible to select by pressing [Numeric] (2)

Example: 28: 2 8

3Press [MENU] (7) to finish the setting mode.

4Retune your TV to the new RF channel for the VCR.

Note:

Even if the RF output channel has been changed, it is not necessary to perform Auto Tuning.

6

Image 6
Contents Contents Video Cassette RecorderFor your safety Inserting Remote Control BatteriesCondensation may form in the following cases Controls and Components 5453Prog Play Picture ModeTimer Check Prog Guide PROG/CHECKConnections Setting the Remote Control to Operate Your TVConnection to a TV using the Audio/Video Input Socket Basic ConnectionsPress Menu Tuning the TV to Your VCRTo Change the RF output Channel Operations Hold down Menu 7 for 5 seconds or moreStoring TV Broadcasts in Your VCR Auto Tuning Using the On Screen Display For AustraliaAuto Tuning Using the On Screen Display For New Zealand Pre-programmed TV Channels Australia onlySetting the Clock of Your VCR Settings Using the On Screen Display To Make Various Indicators Appear On Screen DisplayTo Set the Colour TV System JET Navigator Option SettingTape Select OSD RECPlayback To Play Back a Recorded Part RepeatedlyNtsc Playback Recording To reset the tape counter To Display the Approximate Remaining Tape TimeTo Stop the OTR Recording Before the End VCR in tape refresh standby Recording from an external sourceRecording VCR ModeTimer Recording Key ProgrammingWeekly Timer Recording To Suspend the Timer Recording Standby ModeSetting other Programmes in Succession Daily Timer RecordingChecking a Timer Programme Cancelling a Timer ProgrammePress PROG/CHECK 14 twice Recorded by the character Category setting allows you toTo Set the Category Icon indicationsTo Demonstrate the Jet Navigator Function When Recording Over the Same Location on a TapeTo Cancel the Index Search or to Stop Playback Press Stop To Check the Recorded Programming Data Time Stamp FunctionOperation Press Prog Play Before Requesting ServiceTo Cancel the Easy Programme Playback Message of On Screen DisplayAdjusting the Playback Picture Crystal View ControlDirt on the video heads Specifications