Panasonic AJ-SD755 Reel Rota VTR Stop TOO Fast, Torque ERR VTR Stop, CAP Tension, Reel DIR, Drum

Page 67

Error messages

Error messages

Display	ODescription
Display	OVTR operation and corrective action
	OVTR operation and corrective action


E-64	If the supply reel motor speed is abnormally
	high, the error number flashes on the display.
S REEL ROTA	VTR: STOP
TOO FAST	OSet the POWER switch to OFF and then to
	ON again.

E-67	If the take-up reel motor speed is abnormally
	high, the error number flashes on the display.
T REEL ROTA	VTR: STOP
TOO FAST	OSet the POWER switch to OFF and then to
	ON again.

E-69	If excess torque being applied to the take-up
	reel motor is detected, the error number flashes
T REEL	on the display.
TORQUE ERR	VTR: STOP
	OSet the POWER switch to OFF and then to
	ON again.

E-70	If excess torque being applied to the supply reel
	motor is detected or an abnormal current flowing
S REEL	to the current detection resistor is detected, this
TORQUE ERR	error number flashes on the display.
	VTR: STOP
	OSet the POWER switch to OFF and then to
	ON again.

E-71	If abnormal tension at the supply side is
	detected in the capstan mode, the error number
CAP TENSION	flashes on the display.
ERROR	VTR: STOP
	OSet the POWER switch to OFF and then to
	ON again.

E-72	If abnormal tension at the supply side is
	detected in the reel mode, the error number
REEL	flashes on the display.
TENSION	VTR: STOP
ERROR	OSet the POWER switch to OFF and then to
	ON again.

E-73	If the take-up reel motor has rotated in the
	reverse direction, this error number flashes on
REEL DIR	the display.
UNMATCH	VTR: STOP
	OSet the POWER switch to OFF and then to
	ON again.

E-74	If excess torque being applied to the cylinder
	motor is detected, this error number flashes on
DRUM	the display.
TORQUE	VTR: STOP
ERROR	OSet the POWER switch to OFF and then to
	ON again.

E-78	If a problem has been encountered in
	communication	between	the	servo
M-IF COMM	microcomputer and mechanism relay board, this
ERROR	error number flashes on the display.
	VTR: STOP
	OSet the POWER switch to OFF and then to
	ON again.

Consult your dealer if the error message is still displayed even after restarting the unit.

67

Image 67

Contents Model No. AJ- P Operating Instructions$ this Apparatus Must be Grounded Introduction ContentsFeatures Video Parts and their functionsFront panel DvcproFF button Play buttonREC button Stop buttonShtl PlayerRecorder JOGReview PreviewVAR UnityEXT PresetOFF RegenDisplay panel REC Edit RECREC INH IN/OUT Rear panelOUT = Signal GND terminal Parallel Remote connectorAnalog Audio OUT connectors Cmonitor OUT connectorsOFF ConnectionsSource machine RecorderEditing controller AV monitor Reference signal GeneratorConnections with editing controller Recorder AV monitorCassette size TapesConsumer-use DV and Dvcam cassettes CassettesJog/Shuttle Jog modeInsert Manual editingPreroll AssembleAutomatic editing deck-to-deck Switch settings and adjustmentsWhen using the AJ-SD755 as the recorder When using the AJ-SD755 as the playerAssem Selecting the editing modeMatch frame processing function Checking and previewing edit points How to calculate the durationRe-registering an edit point Modifying edit pointsAuto tag function recorder side Executing and reviewing automatic editingPost-rolling Retry functionAudio split editing Match frame processing system $ Duration displayBetween the video in and OUT points Between the audio in and OUT pointsVariable memory editing Variable memory editing operation procedure$ Selecting the variable memory mode $ Releasing variable memory modeSetup initial settings Changing the settingsSystem Setup menusSetting and releasing the lock mode Changing the fileMenu screen Load/save Lock mode can be setLock mode can be set Counter display Loading user filesMenu screen Saving user filesSystem menu Local SET UP LevelOffset SYS SC/HUser menu Basic Basic User menuOperation Memory stop function INH REC INHLamp Eject SWInterface Edit CF ADJ SEL AUD EditAUD Edit OUT Auto EntryTape Protect Time Code Vaux RUN ModeVitc OUT SBCINT SG YC SEP ModeESR Mode CCR ModeCmpst OUT SetupCmpst CUTINT Umid GENUmid POS CH2 OUT LV CH1 in LVCH2 in LV CH1 OUT LVUser menu Audio REF Level DV PB ATTREC PT Mute DV OutputREC LINE2 BlankADD Line REC LINE1REC LINE13 Number of lines which can be set for TeletextTeletext DETMenu User bit Setting the internal time codeTime code/user bit Time codeLTC Setting the external time codeVitc Display position Operation modeSuperimpose screen Characters displayedInternal synchronization Video output signals and servo reference signalExternal synchronization of video output signals REF Video input signalServo reference signal Audio V fade function Audio signal aFade is performed instantaneously to eliminate the noise Monitor output channel Audio recording channel and monitor output selectionPrinted circuit board Audio recording channelRack-mounting adaptors Rack mountingStandard rack Fasten it to the rack with set screws Attaching the dust cover Video head cleaningMaintenance Condensation$ Warning information display Error messagesDiag menu $ Displaying the Diag menu$ Umid information display $ Displaying the Hours Meter informationInvalid Audio SIG High Error RateUnknown SIG Invalid Video SIGError messages Reel Tension VTR Stop ErrorTorque VTR Stop Error Reel Rota VTR Stop TOO FastRS-232C interface Hardware specificationsExternal interface specifications Connector specificationsCommunication parameters Software specifications ProtocolSend format controller PC 5 VTR $ When the communication has terminated normally Error code tableReturn format VTR 5 controller PC $ Commands relating to operation control Command tableStatus STX QOP ETX $ Commands relating to inquiriesCTL/TC Data STX QCD ETX RequestSdti interface Precautions to observe when using the Sdti signalsSource Reference signal Generator Sdti signalsRemote IN/OUT Connector signalsRemote OUT SUB 25-pin crossover cable supported RS-232CSpecifications Other Input/Output Connectors Technical Support Panasonic Broadcast & Television Systems CompanyEastern Zone Western Zone