Pelco dx4000 manual Alarm Menu, Use the Alarm menu to set up alarms and relays for cameras

Page 21

ALARM MENU

Figure 16. Alarm Menu

Use the Alarm menu to set up alarms and relays for cameras.

•Alarm Input Setup: Use this option to connect or disconnect alarms for any camera at any time. If you connect an alarm, you must associate it with a camera and select the alarm type - normally closed (N/C) or normally open (N/O).

•Relay Output Setup: Use this option to set up a relay in response to alarms. For each alarm, you can enable or disable the relay, select whether the relay mode is latched or transparent, and set the delay time.

A latched relay continues operating for the duration set for it even if an alarm is received but the alarm sensor stops working. A transparent relay stops working if the alarm sensor stops working after it receives an alarm.

Duration refers to either the delay between the occurrence of an alarm and the time at which a relay starts or the length of time that the relay remains in effect after the alarm occurs. Duration times can be increased by 5- or 10-second increments for the first minute, and then by one- or two-minute increments for a maximum of five minutes. Duration may also be set to continue until an operator responds and turns off the alarm with a key (Until Key-In).

•Relay Type: Use this option to indicate whether a relay is normally open (N/O) or normally closed (N/C).

C2602M-C (3/07)

21

Image 21

Contents DX4000 Digital Video Recorder Page Contents Page List of Figures List of Tables Radio and Television Interference Regulatory NoticesDescription Models FeaturesOverview of the System Connecting Devices to the DX4000DX4000 Controls Controls on the Front Panel of the DX4000T u ~í ~â Control Buttons on the Front Panel Video Control Buttons on the Front Panel of the DX4000U ~í ~â Operating the DX4000 from the Remote ControlBefore You Begin Starting and Stopping the DX4000To start the DX4000 To stop the DX4000 Choosing a User AccountMain Window Overview Changing the Display Mode To change the screen sequencing modeChanging the Information Displayed on the Monitor Display Menu Adjusting Menu SettingsRecord Menu Audio Menu Camera MenuUse the Alarm menu to set up alarms and relays for cameras Alarm MenuSystem Menu System MenuPassword Menu Changing PasswordsTo reset the passwords Resetting PasswordsFactory Default Reset Warning Message Factory Default SettingsScreen Rotation Mode Changing the Screen LayoutScreen View Selection Adjusting the Focus or Iris on a Camera Controlling Cameras from the DX4000PAN, TILT, and Zoom Controls To create a preset Working with PresetsTo run a preset To run a predefined presetUsing Preset To set up a patternWorking with Patterns Modifying Camera Settings To modify camera settingsTo run a pattern C2602M-C 3/07 To modify audio recording settings Modifying Audio SettingsTo modify live audio settings To modify image recording settings Modifying Image Recording SettingsModifying Alarms and Relays To modify alarm inputsTo modify relay outputs C2602M-C 3/07 Creating Recording Schedules Setting UP a Recording ScheduleC2602M-C 3/07 Motion Detection Setup Menu Setting UP Motion Detection RecordingC2602M-C 3/07 Setting UP ALARM-BASED Recording C2602M-C 3/07 To change the screen mode To view a specific video channel in single modeMonitoring Live Video Searching for Video Working with Recorded VideoTimeline Showing Available Recorded Video C2602M-C 3/07 Backing UP Video Playing Recorded VideoTo back up video Missing Media Warning Message Working with the Remote Agent Application About the Remote AgentOverview of the Main Screen Starting and Stopping the Remote Agent Remote Agent Control ButtonsTo start the remote agent To stop the remote agentConfiguring the Remote Agent To configure optional settings on the remote agentTo create a network connection for the DX4000 Configuring the DX4000 from the Remote Agent Configuring the DX4000 from the Remote AgentRecording Settings To set up recording qualityTo set up recording schedules To set up alarm recording To set up motion detectionAppears and the Remote Agent tab is displayed C2602M-C 3/07 To configure cameras Camera SettingsAudio Settings To set up audio recordingTo set up live audio To set up alarm inputs and relay outputs Alarm SettingsSystem Settings To configure buzzer soundsTo review system information To modify passwords To configure the disk write modeTo disconnect remote agent connections Controlling Cameras from the Remote Agent To set the network speedTo control PTZ cameras To adjust the focus To adjust the irisLook for the Iris button on the PTZ controls Completing the Setup for a Pattern To set up a presetUsing Preset To use PresetMonitoring Live Video from the Remote Agent To listen to or disable audioCapturing Live Video from the Remote Client Controlling AudioSearching for Recorded Video Working with Recorded Video on the Remote AgentClick the Log button . The Search Log screen appears To search by date or timeBacking UP Video To search by eventClick the Search Events button Save as... dialog box appears To save a snapshotPrint screen appears To print a snapshotViewing Video with the Backup Player To view recorded video with the backup player To authenticate recorded video with the backup playerClick the Open file button. The following screen appears Starting the WEB Client About the Web ClientMonitoring Video with the Web Client Click the Connect button . The Login dialog box appearsC2602M-C 3/07 Product Warranty and Return Information ISO9001

Related manuals

Manual 36 pages 44.82 Kb

Manual 74 pages 2.6 Kb