Pelco dx4000 manual System Settings, To review system information, To configure buzzer sounds

Page 60

SYSTEM SETTINGS

Use the System tab to configure general system information for the DX4000. Some information can be reviewed on this tab but not changed. Buzzer sound settings, passwords, disk write mode, and network connection and speed can be configured on the tab.

TIP: Refer to the System tab when you need to locate the software version number. The information on this tab is useful when troubleshooting the system or upgrading to a newer version.

Figure 74. Configuring System Settings from the Remote Agent

To review system information

1. From the remote agent application main screen, click the Setup button

if the Settings screen is not open. The Settings screen

appears and the Remote Agent tab is displayed.

 

2.Open the DVR System tab, and then click the System tab.

3.Review the following general system information:

S/W Version: This is the version number of the firmware installed on the DX4000.

H/W Version: This is the version number of the motherboard installed on the DX4000.

Video Signal Type: This is the type of video signal that you are recording from the cameras. Video signal types can be NTSC or PAL.

Disk Size: This is the size of the hard disk drive. If two hard disk drives are installed on the DX4000, this number is the size of the primary hard disk drive.

Number of HDD: This is the number of hard disk drives installed on the DX4000. A maximum of two hard disk drives may be installed on the unit.

IP Address: This is the IP address of the DX4000. Use this address when connecting to the DX4000 from the remote agent application or the web client.

MAC Address: This is the MAC address of the DX4000. Use this address to connect to the DX4000 from the remote agent application if your network uses a DDNS to derive IP addresses.

4.Click the OK button to close the screen.

To configure buzzer sounds

1. From the remote agent application main screen, click the Setup button

if the Settings screen is not open. The Settings screen

appears and the Remote Agent tab is displayed.

 

60

C2602M-C (3/07)

Image 60
Contents DX4000 Digital Video Recorder Page Contents Page List of Figures List of Tables Regulatory Notices Radio and Television InterferenceDescription Features ModelsConnecting Devices to the DX4000 Overview of the SystemDX4000 Controls Controls on the Front Panel of the DX4000T u ~í ~â Video Control Buttons on the Front Panel of the DX4000 Control Buttons on the Front PanelOperating the DX4000 from the Remote Control U ~í ~âBefore You Begin Starting and Stopping the DX4000To start the DX4000 Choosing a User Account To stop the DX4000Main Window Overview Changing the Display Mode To change the screen sequencing modeChanging the Information Displayed on the Monitor Adjusting Menu Settings Display MenuRecord Menu Camera Menu Audio MenuAlarm Menu Use the Alarm menu to set up alarms and relays for camerasSystem Menu System MenuChanging Passwords Password MenuResetting Passwords To reset the passwordsFactory Default Settings Factory Default Reset Warning MessageScreen Rotation Mode Changing the Screen LayoutScreen View Selection Adjusting the Focus or Iris on a Camera Controlling Cameras from the DX4000PAN, TILT, and Zoom Controls Working with Presets To create a presetTo run a preset To run a predefined presetUsing Preset To set up a patternWorking with Patterns Modifying Camera Settings To modify camera settingsTo run a pattern C2602M-C 3/07 Modifying Audio Settings To modify audio recording settingsTo modify live audio settings Modifying Image Recording Settings To modify image recording settingsModifying Alarms and Relays To modify alarm inputsTo modify relay outputs C2602M-C 3/07 Setting UP a Recording Schedule Creating Recording SchedulesC2602M-C 3/07 Setting UP Motion Detection Recording Motion Detection Setup MenuC2602M-C 3/07 Setting UP ALARM-BASED Recording C2602M-C 3/07 To change the screen mode To view a specific video channel in single modeMonitoring Live Video Working with Recorded Video Searching for VideoTimeline Showing Available Recorded Video C2602M-C 3/07 Playing Recorded Video Backing UP VideoTo back up video Missing Media Warning Message Working with the Remote Agent Application About the Remote AgentOverview of the Main Screen Remote Agent Control Buttons Starting and Stopping the Remote AgentTo start the remote agent To stop the remote agentConfiguring the Remote Agent To configure optional settings on the remote agentTo create a network connection for the DX4000 Configuring the DX4000 from the Remote Agent Configuring the DX4000 from the Remote AgentRecording Settings To set up recording qualityTo set up recording schedules To set up alarm recording To set up motion detectionAppears and the Remote Agent tab is displayed C2602M-C 3/07 Camera Settings To configure camerasAudio Settings To set up audio recordingTo set up live audio Alarm Settings To set up alarm inputs and relay outputsSystem Settings To configure buzzer soundsTo review system information To modify passwords To configure the disk write modeTo disconnect remote agent connections Controlling Cameras from the Remote Agent To set the network speedTo control PTZ cameras To adjust the focus To adjust the irisLook for the Iris button on the PTZ controls To set up a preset Completing the Setup for a PatternTo use Preset Using PresetTo listen to or disable audio Monitoring Live Video from the Remote AgentCapturing Live Video from the Remote Client Controlling AudioWorking with Recorded Video on the Remote Agent Searching for Recorded VideoTo search by date or time Click the Log button . The Search Log screen appearsBacking UP Video To search by eventClick the Search Events button To save a snapshot Save as... dialog box appearsTo print a snapshot Print screen appearsViewing Video with the Backup Player To view recorded video with the backup player To authenticate recorded video with the backup playerClick the Open file button. The following screen appears About the Web Client Starting the WEB ClientClick the Connect button . The Login dialog box appears Monitoring Video with the Web ClientC2602M-C 3/07 Product Warranty and Return Information ISO9001
Related manuals
Manual 36 pages 44.82 Kb Manual 74 pages 2.6 Kb