Pelco C2602M-a, dx4000 manual System Settings, To set up alarm inputs and relay outputs

Page 59

To set up alarm inputs and relay outputs

1. From the remote agent application main screen, click the Setup button

if the Settings screen is not open. The Settings screen

appears and the Remote Agent tab is displayed.

 

2.Open the DVR System tab, and then click the Alarm tab.

3.Under Alarm Input, configure the following settings for each camera:

•Status: Set this to Connected or Disconnected.

•Camera Input: Select the alarm input channel that is associated with the camera. Choices are 1 through 4.

•Type: Select the type of alarm. Choices are Normally Open and Normally Closed.

4.Under Relay Output, configure the following settings for each camera:

•Relay Out: Set this to On or Off. When the relay is turned on, it will respond to an alarm at the associated camera.

•Mode: Set the relay mode to Transparent or Latched. A transparent relay stops working if the alarm sensor stops working after it receives an alarm. A latched relay continues operating for the duration set for it even if alarm is received but the alarm sensor stops working.

•Duration: Select the length of time after an alarm is received that the relay will continue to operate. Duration refers to either the delay between the occurrence of an alarm and the time at which a relay starts or the length of time that the relay remains in effect after the alarm occurs. Duration times can set for 5- or 10-second increments for the first minute, and then in one- or two-minute increments for a maximum of five minutes. Duration may also be set to continue until an operator responds by turning off the alarm with a key (Until Key-In).

5.Click the Apply button to save the changes and continue to other settings. If you are finished updating settings, click the OK button to close the screen.

SYSTEM SETTINGS

Use the System tab to configure general system information for the DX4000. Some information can be reviewed on this tab but not changed. Buzzer sound settings, passwords, disk write mode, and network connection and speed can be configured on the tab.

TIP: Refer to the System tab when you need to locate the software version number. The information on this tab is useful when troubleshooting the system or upgrading to a newer version.

Figure 73. Configuring System Settings From the Remote Agent

C2602M-A (6/06)

59

Page 58 Page 60
Image 59
Page 58 Page 60
Contents DX4000 Digital Video Recorder Contents C2602M-A 6/06 List of Figures List of Tables Description Models FeaturesOverview of the System Connecting Devices to the DX4000Controls on the Front Panel of the DX4000 DX4000 ControlsControl Buttons on the Front Panel Video Control Buttons on the Front Panel of the DX4000Operating the DX4000 from the Remote Control To start the DX4000 Before You BeginStarting and Stopping the DX4000 To stop the DX4000 Choosing a User AccountMain Window Overview Changing the Information Displayed on the Monitor Changing the Display ModeTo change the screen sequencing mode Display Menu Adjusting Menu SettingsRecord Menu Audio Menu Camera MenuUse the Alarm menu to set up alarms and relays for cameras Alarm MenuSystem Menu System MenuBack UP Menu Backup MenuPassword Menu Changing PasswordsTo reset the passwords Resetting PasswordsFactory Default Reset Warning Message Factory Default SettingsScreen View Selection Screen Rotation ModeChanging the Screen Layout PAN, Tilt and Zoom Controls Adjusting the Focus or Iris on a CameraControlling Cameras from the DX4000 To run a predefined preset Working with PresetsTo create a preset To run a presetWorking with Patterns Using PresetTo set up a pattern To run a pattern Modifying Camera SettingsTo modify camera settings C2602M-A 6/06 To modify audio recording settings Modifying Audio SettingsTo modify live audio settings To modify image recording settings Modifying Image Recording SettingsTo modify alarm inputs Modifying Alarms and RelaysTo modify relay outputs Creating Recording Schedules Setting UP a Recording ScheduleC2602M-A 6/06 Motion Detection Setup Menu Setting UP Motion Detection RecordingC2602M-A 6/06 Setting UP ALARM-BASED Recording C2602M-A 6/06 Monitoring Live Video To change the screen modeTo view a specific video channel in single mode Searching for Video Working With Recorded VideoTimeline Showing Available Recorded Video C2602M-A 6/06 To back up video Playing Recorded VideoBacking UP Video Missing Media Warning Message Overview of the Main Screen Working With the Remote Agent ApplicationAbout the Remote Agent To stop the remote agent Remote Agent Control ButtonsStarting and Stopping the Remote Agent To start the remote agentTo create a network connection for the DX4000 Configuring the Remote AgentTo configure optional settings on the remote agent Configuring the DX4000 from the Remote AgentTo set up recording quality Recording SettingsTimer Recording Setup Screen To set up recording schedulesTo set up motion detection To set up alarm recordingC2602M-A 6/06 To configure cameras Camera SettingsTo set up audio recording Audio SettingsTo set up live audio Alarm SettingsTo set up alarm inputs and relay outputs System SettingsTo configure buzzer sounds To modify passwordsTo review system information To set the network speed To configure the disk write modeTo disconnect remote agent connections To control PTZ cameras To adjust the focusControlling Cameras from the Remote Agent Controlling Audio To listen to or disable audioMonitoring Live Video from the Remote Agent Capturing Live Video from the Remote ClientUse the following buttons to review the recorded video Working with Recorded Video on the Remote AgentSearching for Recorded Video Click the Log button . The Search Log screen appears To search by date or timeEvent Viewer Screen To search by eventBacking UP Video Remote Agent Backup ScreenPrint screen appears To save a snapshotTo print a snapshot Save as... dialog box appearsViewing Video with the Backup Player Click the Open file button. The following screen appears To view recorded video with the backup playerTo authenticate recorded video with the backup player Starting the WEB Client About the Web ClientMonitoring Video with the Web Client Click the Connect button . The Login dialog box appearsProduct Warranty and Return Information ISO9001
Related manuals
Manual 74 pages 2.69 Kb Manual 36 pages 44.82 Kb Manual 78 pages 11.82 Kb
Top Page Image Contents