JVC HR-S8700EK SET Tape Speed, SET PDC Mode, Return to Normal, Screen, Engage RECORDER’S

Page 21

ENTER PRESET POSITION

 

Press PR +/– to enter the

 

– P1 –

 

preset position corre-

 

 

 

 

6 sponding to the broadcast-

START

STOP

21:00

= 22:00

 

ing station you wish to

SP

VPS/PDC OFF

 

record.

 

 

 

 

DATE

TV PROG

 

 

 

25.12

1

 

 

 

[+/–] =

BBC 1

 

 

 

[0]:SAT

 

 

 

[PROG] : EXIT

 

 

 

 

SP

 

 

SET TAPE SPEED

 

7 Press SP/LP/EP (

) to set the tape speed.

8

SET PDC MODE

 

Press PDC to select "ON" or "OFF".

 

If "VPS/PDC ON" is displayed on the screen or "VPS/

PDC" is lit on the display panel, PDC is set to ON.

If "VPS/PDC OFF" is displayed on the screen or "VPS/

 

PDC" is not lit on the display panel, PDC is set to OFF.

☞"PDC Recording" in the right column.

● VPS (Video Programme System) recording is not currently available in the U.K. and not possible with this recorder.

RETURN TO NORMAL

SCREEN

After confirming all information is correct, press PROG

or OK. "PROGRAM COMPLETED" appears on the

9 screen for about 5 seconds, then normal screen

appears. If the timer programme is overlapped with

another one that was already set, "PROGRAM

OVERLAPPED" appears on screen and "Err" appears on

the front display panel. (☞ pg. 23)

● Repeat steps 1 – 9 for each additional programme.

21

Satellite Receiver Users

To timer-record a satellite broadcast using Express Timer Programming:

1 Perform "Satellite Receiver Control Setting" (☞ pg. 12). 2 Perform steps 1 – 10. In step 6, press the NUMBER key "0" to change "TV PROG" to "SAT". The display panel

shows "L2" for the preset position. Then press PR +/– to enter the preset position for the satellite broadcast. In step 8, you cannot set PDC to ON.

3 Leave the satellite receiver's power on.

PDC Recording

Now available from some TV stations, PDC (Programme Delivery Control) is a service designed to assure safe, accurate timer recording. With this system, special code signals are transmitted together with the audio/video signals. These code signals control your video recorder and have precedence over the advertised times which you may have preset into the timer. This means that your recorder will start and stop recording when the preset TV programmes actually start and end — even if the broadcast time of a preset TV programme is changed from what has been advertised. PDC is currently available nationally on BBC1, BBC2, Ch.4 and Ch.5, except from a few small relay transmitters. Ch.3 operates a PDC service in some areas. All channels intend to offer this service in due course. Check your TV programme listing guide for latest informa- tion. If the channel you intend to record does not offer a PDC service your recorder will not start recording if PDC has been selected. Be sure to set PDC to "OFF" if PDC is not available on your selected channel.

(☞ step 8 in the left column).

NOTES:

● Set the start time (PDC time) exactly as advertised in the TV listing. A different time than advertised will result in no recording.

● PDC recording is also possible when a satellite receiver or a cable system is connected to AV2 (L-2) IN/DECODER on your recorder.

● PDC recording is also possible via the AV1 (L-1) IN/OUT connector.

 

ENGAGE RECORDER’S

10

TIMER MODE

Press ä (TIMER). The recorder turns off automatically

and ä appears on the display panel.

 

● To disengage the timer, press ä (TIMER) again.

Timer Warning

If you have programmed your recorder to timer-record a programme or a series of programmes, a warning appears on the screen to tell you that the recording is due to start in 5 minutes.

–WARNING– TIMER RECORDING

TO START SOON

[]

To Timer-Record Weekly Or Daily Serials . . .

. . . anytime during steps 2 through 9, press WEEKLY (NUMBER key “9”) for weekly serials or DAILY (NUMBER key “8”) for daily serials (Monday – Friday). Either "WEEKLY" or "DAILY" appears on the screen. Pressing the button again makes the corresponding indication disappear.

NOTE:

You can programme this recorder to timer-record as many as 8 programmes. If you try to programme the recorder to record a ninth, "PROGRAM FULL" appears on screen and "FULL" appears on the front display panel. To record the extra programme, you must first cancel any unnecessary programmes (☞ pg. 22).

NOTES:

●The warning only appears if you’re not in the Timer mode at the time.

●If this recorder is being used as the player for tape dubbing, the warning screen will be recorded on the tape in the other video recorder.

The warning blinks for the entire 5 minutes leading up to the start of timer recording. To clear the display, press .

Page 20 Page 22
Image 21
Page 20 Page 22
Contents HR-S8700EK Connection to the mains supply in the United Kingdom Safety PrecautionsDo not place the recorder Moisture CondensationSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Connect Video Recorder to TV Back of TVBack of Recorder Video Connection Mains outlet Mains Power CordWith the AV or S-VIDEO connection Before performing the following procedure, make sure thatTion pg and the TV is turned on, Go to item10 or If -- appears on the display panel, refer Remote control while downloading isLink screen will appear. Then the Guide Program number setIf both auto channel set and auto clock set have failed If auto channel set has succeeded but auto clock set has notAccess Mode SET Screen Access Main Menu ScreenLink Functions Turn on the RecorderSatellite Receiver Control Setting Enter Satellite RECEIVER’S Brand Select Satellite RECEIVER’S Channel for TestingCheck Result of Test CodeLoad a Cassette PlaybackFind Programme Start Point Start PlaybackActivate HIGH-SPEED Search Pause During PlaybackRecording Reset Counter Select Preset to WatchEngage ITR Mode SET Counter DisplayAccess Video PLUS+ Screen Video Plus+ Timer ProgrammingAccess Video PLUS+ Program Screen Enter Pluscode NumberPDC Recording Timer WarningEnter Programme Express Timer ProgrammingStart Time TimeTimer Mode SET PDC ModeSET Tape Speed Return to NormalCheck, Cancel And Replace Programmes Cancel or Change Programme Setting When programmes overlap each otherConfirm Overlapping Programmes ModifyNavigation Return to Normal Screen Check MemoryTurn OFF Navigation Turn Off NavigationTitle Editing Access Find Blank Space ScreenSelect Tape Number Load a CassetteEnter Character Access Video Navigation ScreenEdit Tape Title Select Tape NumberSelect Programme Select CategoryEdit Programme Title Category Data Delete ProgrammeDelete Tape Data Delete Programme DataAccess Tape NO. Screen Access Find Title ScreenAccess Video Finding TitleSelect Programme Access Category Screen Access Date ScreenSelect Programme Load a Cassette Sorting By DateNavigation Check Memory Title Editing Access Main Menu Screen Select Programme Return to Normal Screen Finding Title Access Date Screen Adjust Tracking Playback Picture AdjustmentOverride Automatic Tracking ManuallyMode SET ModeDigital 3R Video StabilizerAdjust Audio Access REC LevelSelecting Sound You Want Control ScreenSoundtrack Selection Receiving Nicam Stereo And Bilingual ProgrammesDuring Playback Type of Broadcast On-screen Display Being ReceivedActivate Index Search Looking For Scene You WantSkip Over Unwanted SectionsSelect S-VHS Mode Recording According To Tape TypeSuper VHS S-VHS VHS ET and VHS Select B.E.S.T. Mode Playback/ Recording According To Tape Charac- teristicsS.T. Picture System Recording Start PlaybackPlayback During B.E.S.TAutomatic Satellite Programme Recording Connector TV Aerial cable Audio in connectorSatellite Receiver Unit AerialSelect L-2 Select Mode Access Main Menu ScreenREC Mode ScreenRemove Power Supply Remote Control FunctionsSET Remote Control Code RE-SUPPLY PowerTV Multi-Brand Remote Control Control Your TV Using Additional ButtonsSET TV Brand Code Operate TVBrand Code Satellite Receiver Multi Brand Remote ControlOperate Satellite Receiver NumberAccess Mode SET Access Main MenuControl SET Mode Minimizing Picture Degradation While EditingEdit From Camcorder Synchro Edit connector Lanc Cable not provided Synchro EditingPress Synchro /8again Repeat steps 4 6 as necessary SET Edit Mode Input ModeEdit To Or From Another Video Recorder SET Recording DECK’SRecorder Player SELECT/INPUT Setting OUTPUT/INPUT SettingAudio Dubbing Reset the Counter Insert EditingLocate END Point Start Editing Engage Insert EditingEND Insert Editing Press InsertAccess Initial SET Screen Terminal JLIPJoint Level Interface Protocol ConnectorAccess Jlip ID NO. SET Screen Information On J TerminalOther Functions ENABLE/DISABLEON-SCREEN Display On-Screen DisplaySelect Power Save Mode Power Save ModePress %Þ to move the highlight bar pointer to Auto Timer Access Mode SET ScreenAuto SP→LP Timer Next Function MemoryEngage RECORD-PAUSE Mode Stop PlaybackResume Recording Speaker Television Connection To Stereo SystemExit Video Channel SET Mode Access Video Channel SET ModeVideo Channel Set SET Video ChannelWith RF Connection Test SignalPerform Auto Channel SET Tuner SetAuto Channel Set Pointer to Auto CHView Confirmation Screen Input Channel Storing Channels ManuallyEnter NEW Channel Information Close Confirmation ScreenChange Station Preset Position When Receiving a Scrambled BroadcastFine-Tuning Channels Already Stored Delete a ChannelEnter NEW Character Station Name TV Station And ID ListTV Station Channel Number Guide Clock Set Video Plus+ System Setup NumberGuide Program Number Set Questions And Answers Ä remain lit on the display panel. Is there Problem?What happens if the tape runs out during recording? Troubleshooting Recording Won’t stop blinking Record Safety tab removedOther Problems Front View IndexRear View VCR Display PanelTV Muting Button mutes sound Remote ControlFast Forward FF Button same as button on Remote Control LCDDA4 Double Azimuth helical Maximum recording time
Top Page Image Contents